Axis Communications P1354-E user manual Connectors

Page 8

AXIS P1354–E Network Camera

Hardware Overview

15.Bracket screws (4x)

16.Bracket adapter

17.Network cable (route through wall bracket). Cable not included

18.Wall bracket

19.Bracket adjustment screw

Connectors

For technical specifications, see page 60.

Network connector - RJ45 Ethernet connector. Supports Power over Ethernet (PoE).

NOTICE

The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network switch shall be shielded (STP) and intended for their specific use. Make sure that the network switch is properly grounded. For information about regulatory requirements, see Regulatory Information, on page 2 .

Audio in (pink) - 3.5 mm input for a mono microphone, or a line-in mono signal (left channel is used from a stereo signal).

Audio out (green) - 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier. A stereo connector must be used for audio out.

SD card slot - A standard or high-capacity microSD card (not included) can be used for local recording with removable storage.

NOTICE

To prevent corruption of recordings, the SD card should be unmounted before removal. To unmount, go to Setup > System Options > Storage > SD Card and click Unmount.

Control button - The control button is used for:

Enabling the Focus Assistant. Press and very quickly release the Control button.

Resetting the product to factory default settings. See page 54.

Connecting to an AXIS Video Hosting System service. See page 47. To connect, press and hold the button for about 1 second until the Status LED flashes green.

Connecting to AXIS Internet Dynamic DNS Service. See page 48. To connect, press and hold the button for about 3 seconds.

Power connector - 2-pin terminal block for power input. Use a limited power source (LPS) with either a rated output power limited to 100 W or a rated output current limited to 5 A.

I/O terminal connector - Use in applications for e.g. motion detection, event triggering, time lapse recording and alarm notifications. In addition to an auxiliary power and a GND pin, the I/O terminal connector provides the interface to:

Digital output – For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, output buttons on the Live View page or by an Action Rule. The output will show as active (shown under System Options > Ports & Devices) if the alarm device is activated.

Digital input – An alarm input for connecting devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a signal is received the state changes and the input becomes active (shown under System Options > Ports & Devices).

Note

The I/O connector is connected to the housing (fan/heater) on delivery, and will trigger an input port event to indicate a fan or heater error when activated. See Events, on page 39 for information about events.

8

Image 8
Contents Axis P1354-E Network Camera About this document LiabilityIntellectual Property Rights Equipment ModificationsSupport Learn MoreTable of Contents Axis P1354-E Network CameraTechnical Specifications Hardware Overview Hardware OverviewAxis P1354-E Network Camera Connectors LED Indicators Status LED when using Focus AssistantReplacing the lens Color IndicationUnscrew the standard lens Attach and screw on the new lens Access from a Browser Accessing the ProductAccessing the Product Accessing the Product Access from the Internet Set the Root PasswordNetwork TCP/IP Advanced Click Create self-signed certificateLive View Accessing the Product Set Power Line FrequencyPTZ Mode Go to Setup Events Controls on the Live ViewAxis Media Control viewer toolbar Manual TriggerPTZ Controls AMC Audio ControlsAxis P1354-E Network Camera How to Stream H.264 Media StreamsMedia Streams Axis Media Control AMCAlternative Methods of Accessing the Video Stream Accessing Audio Streams Setting Up the Product Setting Up the ProductBasic Setup FocusVideo and Audio Video and AudioVideo Stream Pixel CounterImage 264Camera Settings Video and Audio Stream ProfilesIris configuration Iris adjustmentShutter & Gain Set Shutter toImage Settings View AreaOverlay Day/NightAudio Settings Privacy MaskOverlay Image Go to Video & Audio Overlay ImageAudio Modes Audio InputAudio Clips Audio OutputDefault Viewer for Browsers Live View ConfigLive View Config Viewer Settings Go to Setup Live View ConfigUser Defined Links Output ButtonsAxis P1354-E Network Camera Preset Positions Installing a PTZ driverGo to PTZ Preset Positions PTZ Pan Tilt ZoomDevice Settings Guard TourAdvanced ControlsOperator Same as administrator but with lower priority Control QueueDetectors DetectorsCamera Tampering Motion DetectionSet Up Motion Detection Windows Motion Detection ParametersDefault values Audio DetectionLow level 0% Recommended valuesApplications ApplicationsEvents EventsGo to Events Action Rules and click Add Setting Up an Action RulePTZ Control Recipients SchedulesRecipient Use with action Go to Events Recipients and click AddEvents Recurrences Go to Events Recurrences and click AddRecordings RecordingsRecording List Continuous RecordingSystem Options System OptionsSecurity UsersDate & Time IeeeAudio Support CertificatesBasic TCP/IP Settings IPv4 Address ConfigurationIPv6 Address Configuration NetworkAssign IP Address using ARP/Ping Linux/Unix syntaxLinux/Unix example Axis Video Hosting System AvhsAdvanced TCP/IP Settings Https NAT traversal port mapping for IPv4QoS Quality of Service Smtp emailStorage UPnPTMRTP/H.264 BonjourPorts & Devices Network SharePorts COM PortMaintenance SupportReset to Factory Default Settings Plain ConfigScripting File UploadAxis P1354-E Network Camera Troubleshooting TroubleshootingEmergency Recovery Procedure Checking the FirmwareProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product is accessible locally but not externally Problems with streaming H.264Status and Network indicator LEDs are flashing red rapidly Video and image problems, generalSetup Video & Audio Camera Settings SettingsTechnical Specifications Technical SpecificationsFunction/group Specifications Audio Audio streaming Built-in Microphone Specification Network SecurityMaintenance Audio inputFunction/group Specifications Installation aids PowerConnectors DimensionsTechnical Specifications Connectors Terminal connectorFunction Pin Specifications Power connectorAudio connector RS-485/422 connectorPerformance Considerations Audio Input Audio OutputM2.2