Axis Communications M1034-W user manual Events

Page 32

AXIS M1034-W Network Camera

Events

Events

The Axis product can be configured to perform actions when different events occur, for example, start a recording when motion is detected. The set of conditions that defines how and when the action is triggered is called an Action Rule.

Available Action Rule triggers and conditions include:

Detectors

-Audio Detection — trigger the rule when audio is detected, see Audio Detection, on page 31.

-Motion Detection — trigger the rule when motion is detected, see Motion Detection, on page 29.

-PIR — trigger the rule when the PIR sensor detects motion, see PIR Sensor, on page 31.

-Tampering — trigger the rule when tampering is detected, see Camera Tampering, on page 29.

Hardware

-Network — trigger the rule if network connection is lost or restored.

Input Signal

-Digital Input Port — trigger the rule when an I/O port receives a signal from a connected device, see I/O Ports, on page 49.

-Manual Trigger — trigger the rule using the Manual Trigger button in the Live View page, see Controls on the Live View Page, on page 11. This can for example be used to validate actions during product installation and configuration.

PTZ

-Moving — trigger the rule when the camera view moves due to a PTZ operation. This can for example be used as an additional condition to prevent an action rule triggered by motion detection to record video while the camera view moves due to a PTZ operation.

-Preset Reached — trigger the rule when the camera stops at a preset position. This can be for example be used with the Send Images action to upload images from the preset position.

Storage

-Available — trigger the rule when the storage device is unmounted or removed. This can for example be used to send maintenance notifications.

-Full — trigger the rule when the storage device is full. Under normal operation, the oldest recordings will be overwritten to prevent the storage device from becoming full.

-Locked — trigger the rule if the storage device is locked (write protected).

System

-System Initializing — trigger the rule when the product is being started. This can for example be used to send a notification when the product restarts.

Time

-Recurrence — trigger the rule periodically, see Recurrences, on page 34. This can for example be used to upload an image every 5 minutes.

-Use Schedule — trigger the rule according to the selected schedule, see Schedules, on page 34.

Available actions include:

Activate Light — turn the built-in light on or off.

32

Image 32
Contents Axis M1034-W Network Camera About this document LiabilityIntellectual Property Rights Equipment ModificationsLearn More SafetySupport Table of Contents Axis M1034-W Network CameraPerformance Considerations Hardware Overview ConnectorsHardware Overview Color Indication LED IndicatorsPower connector Mini DC connector Axis M1034-W Network Camera Accessing the Product Accessing the ProductAccess from a Browser Start a browser Internet Explorer, Firefox, SafariAccess from the Internet Set the Root PasswordSet Power Line Frequency Network TCP/IP AdvancedLive View Controls on the Live ViewGo to Setup Events Axis Media Control viewer toolbarManual Trigger To show the manual trigger buttons in the Live ViewHalf-duplex mode PTZ ControlsHow to Stream H.264 Media StreamsMedia Streams Axis Media Control AMCAlternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccessing Audio Streams Java applet supports simplex audio with G.711 encodingBasic Setup Setting Up the ProductSetting Up the Product Video and Audio Video and AudioVideo Stream Pixel CounterClick Save to apply the new settings Stream ProfilesImage 264Camera Settings Exposure SettingsView Area Image AppearanceDate/Time Formats in the online help To enable overlays OverlayOverlay Image Go to Video & Audio Video Stream and select the Image tabAudio Settings Privacy MaskAudio Modes Audio InputG711 G726 Audio ClipsAudio Output Live View Config Default Viewer for BrowsersLive View Config Viewer Settings User Defined LinksLight Buttons Browser Viewer DescriptionGo to Setup Live View Config Output ButtonsPreset Positions Go to PTZ Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomOperator Same as administrator but with lower priority AdvancedControl Queue ControlsDetectors DetectorsCamera Tampering Motion DetectionSet Up Motion Detection Windows Motion Detection ParametersAudio Detection PIR SensorEvents EventsSetting Up an Action Rule PTZ ControlRecurrences RecipientsSchedules Axis M1034-W Network Camera Recordings RecordingsRecording List Continuous RecordingAxis M1034-W Network Camera System Options System OptionsSecurity UsersIeee CertificatesClick Install certificate and upload the certificate Date & TimeAudio Support Go to System Options Security CertificatesBasic TCP/IP Settings NetworkAdvanced TCP/IP Settings Https NAT traversal port mapping for IPv4Wireless Settings WirelessWireless Network Status WPATM-/WPA2TM-PSK WPATM-/WPA-EnterpriseEAP-PEAP/MSCHAPv2 No SecurityQoS Quality of Service CertificatesUPnPTM can be disabled under System Options Network UPnPTM Smtp emailUPnPTM RTP/H.264Ports & Devices MaintenanceStorage Support Support OverviewSystem Overview Logs & ReportsReset to Factory Default Settings ScriptingFile Upload Plain ConfigTroubleshooting TroubleshootingEmergency Recovery Procedure Checking the FirmwareProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product is accessible locally but not externally Problems with the H.264 formatStatus and Network indicator LEDs are flashing red rapidly Video and image problems, generalSetup Video & Audio Camera Settings Problems uploading filesSettings Motion Detection triggers unexpectedlyNo audio Poor audio qualityTechnical Specifications Technical SpecificationsMaintenance Installation aids PowerConnectors Function/group Specifications NetworkDimensions HxWxD WeightAccessories Terminal connectorPerformance Considerations M2.3