Axis Communications M1034-W user manual Setting Up an Action Rule, PTZ Control

Page 33

AXIS M1034-W Network Camera

Events

Output Port — activate an I/O port to control an external device.

Play Audio Clip — see Audio Clips, on page 23.

PTZ Control

-Preset Position — go to a preset position.

-Guard Tour — start a guard tour, see Guard Tour, on page 27.

Record Video — record video to a selected storage.

Send Images — send images to a recipient.

Send Notifications — send a notification message to a recipient.

Status LED — flash the LED indicator. This can for example be used to validate triggers such as motion detection during product installation and configuration.

Setting Up an Action Rule

An action rule defines the conditions that must be met for the product to perform an action, for example record video or send email notifications. If multiple conditions are defined, all must be met to trigger the action.

The following example describes how to set up an action rule to record video to a network share if there is movement in the camera’s field of view.

Set up motion detection and add a network share:

1.Go to Detectors > Motion Detection and configure a motion detection window, see page 30

2.Go to System Options > Storage and set up the network share, see page 49.

Set up the action rule:

1.Go to Events > Action Rules and click Add.

2.Select Enable rule and enter a descriptive name for the rule.

3.Select Detectors from the Trigger drop-down list.

4.Select Motion Detection from the drop-down list. Select the motion detection window to use.

5.Optionally, select a Schedule and Additional conditions, see below.

6.Under Actions, select Record Video from the Type drop-down list.

7.Select a Stream profile and configure the Duration settings as described below.

8.Select Network Share from the Storage drop-down list.

To add additional criteria, select the Additional conditions option and add additional triggers. To prevent an action from being triggered repeatedly, a Wait at least time can be set. Enter the time in hours, minutes and seconds, during which the trigger should be ignored before the action rule can be activated again.

The recording Duration of some actions can be set to include time immediately before and after the event. Select Pre-trigger time and/or Post-trigger time and enter the number of seconds. When While the rule is active is enabled and the action is triggered again during the post-trigger time, the recording time will be extended with another post-trigger time period.

For more information, see the online help .

33

Image 33
Contents Axis M1034-W Network Camera Liability About this documentIntellectual Property Rights Equipment ModificationsSafety SupportLearn More Axis M1034-W Network Camera Table of ContentsPerformance Considerations Connectors Hardware OverviewHardware Overview LED Indicators Power connector Mini DC connectorColor Indication Axis M1034-W Network Camera Accessing the Product Accessing the ProductAccess from a Browser Start a browser Internet Explorer, Firefox, SafariSet the Root Password Access from the InternetSet Power Line Frequency Network TCP/IP AdvancedControls on the Live View Live ViewAxis Media Control viewer toolbar Go to Setup EventsManual Trigger To show the manual trigger buttons in the Live ViewPTZ Controls Half-duplex modeMedia Streams How to Stream H.264Media Streams Axis Media Control AMCQuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Accessing Audio StreamsSetting Up the Product Setting Up the ProductBasic Setup Video and Audio Video and AudioVideo Stream Pixel CounterStream Profiles Click Save to apply the new settingsImage 264Exposure Settings Camera SettingsView Area Image AppearanceOverlay Date/Time Formats in the online help To enable overlaysOverlay Image Go to Video & Audio Video Stream and select the Image tabPrivacy Mask Audio SettingsAudio Modes Audio InputAudio Clips Audio OutputG711 G726 Default Viewer for Browsers Live View ConfigLive View Config User Defined Links Viewer SettingsLight Buttons Browser Viewer DescriptionOutput Buttons Go to Setup Live View ConfigGo to PTZ Preset Positions Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomAdvanced Operator Same as administrator but with lower priorityControl Queue ControlsDetectors DetectorsCamera Tampering Motion DetectionMotion Detection Parameters Set Up Motion Detection WindowsPIR Sensor Audio DetectionEvents EventsPTZ Control Setting Up an Action RuleRecipients SchedulesRecurrences Axis M1034-W Network Camera Recordings RecordingsRecording List Continuous RecordingAxis M1034-W Network Camera System Options System OptionsSecurity UsersCertificates IeeeDate & Time Click Install certificate and upload the certificateAudio Support Go to System Options Security CertificatesNetwork Basic TCP/IP SettingsAdvanced TCP/IP Settings NAT traversal port mapping for IPv4 HttpsWireless Wireless Network StatusWireless Settings WPATM-/WPA-Enterprise WPATM-/WPA2TM-PSKNo Security EAP-PEAP/MSCHAPv2Certificates QoS Quality of ServiceSmtp email UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Maintenance StoragePorts & Devices Support Overview SupportSystem Overview Logs & ReportsScripting Reset to Factory Default SettingsFile Upload Plain ConfigTroubleshooting TroubleshootingEmergency Recovery Procedure Checking the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Problems with the H.264 format Product is accessible locally but not externallyVideo and image problems, general Status and Network indicator LEDs are flashing red rapidlySetup Video & Audio Camera Settings Problems uploading filesMotion Detection triggers unexpectedly SettingsNo audio Poor audio qualityTechnical Specifications Technical SpecificationsPower Maintenance Installation aidsConnectors Function/group Specifications NetworkHxWxD Weight DimensionsAccessories Terminal connectorPerformance Considerations M2.3