Axis Communications M1014 user manual Smtp email, UPnPTM, RTP/H.264

Page 37

AXIS M1014 Network Camera

System Options

SMTP (email)

To send email messages from the Axis product via SMTP (Simple Mail Transfer Protocol), an SMTP mail server must be set up. This is done under System Options > Network > SMTP (email).

Enter the host names or IP addresses and port numbers for the primary and secondary mail servers in the fields provided. A From email address is also required. If the mail server requires authentication, check Use authentication to log in to this server and enter the necessary information.

SNMP

The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups.

The Axis product can be configured to support SNMP on the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

SNMP v1/v2 provides the lowest level of security. The community name can be specified as a password for read or read/write access to all supported SNMP devices. The default password for the Read community is public and the default password for the Write community is write.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

Cold start

Warm start

Link up

Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 31. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings, on page 40.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

37

Image 37
Contents Axis M1014 Network Camera About this document SafetyLiability Intellectual Property RightsAxis M1014 Network Camera Table of ContentsHardware Overview ConnectorsHardware Overview Power connector Mini DC connector LED IndicatorsColor Indication Accessing the Product Accessing the ProductAccess from a Browser Set the Root Password Access from the InternetSet Power Line Frequency Network TCP/IP AdvancedLive View Go to Setup EventsControls on the Live View Manual TriggerPTZ Controls Axis Media Control viewer toolbarMedia Streams How to Stream H.264Media Streams Axis Media Control AMCAlternative Methods of Accessing the Video Stream Axis M1014 Network Camera Setting Up the Product Setting Up the ProductBasic Setup Video VideoVideo Stream Pixel CounterImage Stream Profiles264 Exposure Settings Camera SettingsView Area Image AppearanceOverlay Image OverlayGo to Video Video Stream and select the Image tab Go to Video Overlay ImagePrivacy Mask Live View Config Default Viewer for BrowsersLive View Config User Defined Links Viewer SettingsBrowser Viewer Description Go to PTZ Preset Positions Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomControl Queue AdvancedControls Detectors DetectorsCamera Tampering Motion DetectionMotion Detection Parameters Set Up Motion Detection WindowsLow level 0% Default valuesRecommended values Events EventsRecipients Setting Up an Action RuleGo to Events Action Rules and click Add RecipientRecurrences SchedulesGo to Events Recipients and click Add Go to Events Schedules and click AddRecordings RecordingsRecording List Continuous RecordingAxis M1014 Network Camera System Options System OptionsSecurity UsersCertificates IeeeDate & Time Basic TCP/IP SettingsNetwork Go to System Options Security CertificatesAdvanced TCP/IP Settings Host Name Configuration NTP ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4FTP QoS Quality of ServiceSmtp email UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Bonjour StorageSD Card Network ShareSupport MaintenanceSupport Overview System OverviewLogs & Reports Reset to Factory Default SettingsScripting File UploadAxis M1014 Network Camera Troubleshooting TroubleshootingEmergency Recovery Procedure Checking the FirmwareProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Problems with the H.264 format Product is accessible locally but not externallyStatus and Network indicator LEDs are flashing red rapidly Video Camera Settings Video and image problems, generalProblems uploading files Storage and disk management problemsTechnical Specifications Technical SpecificationsPower Maintenance Installation aidsConnectors DimensionsPerformance Considerations M1.8