Axis Communications M1014 user manual Hardware Overview, Connectors

Page 4

AXIS M1014 Network Camera

Hardware Overview

Hardware Overview

	1	4
	2	4
	2	5
	3	5
	3	6
		7
		8
		9

10

11

12

1Status LED indicator

2Focus ring

3Lens

4Network connector (RJ-45)

5Power connector

6Lock ring

7Control button

8SD card slot (microSDHC)

9Power LED indicator

10Network LED indicator

11LED indicator (not used)

12Part number (P/N) & Serial number (S/N)

The Axis product is equipped with a lens with manual focus. It is delivered with the lens prefocused and manual focusing is usually not required.

Note

Only change the focus if required, for example if the image is blurry.

Connectors

For technical speciﬁcations, see page 46.

Network connector - RJ-45 Ethernet connector.

NOTICE

Due to local regulations or the environmental and electrical conditions in which the product is to be used, a shielded network cable (STP) may be appropriate or required. Any network cables that are routed in outdoor environments or similar shall be shielded (STP) and intended for their speciﬁc use. Make sure that the network switch is properly grounded. See Electromagnetic Compatibility (EMC) for regulatory requirements.

4

Image 4

Contents Axis M1014 Network Camera Safety About this documentLiability Intellectual Property RightsTable of Contents Axis M1014 Network CameraHardware Overview ConnectorsHardware Overview Power connector Mini DC connector LED IndicatorsColor Indication Accessing the Product Accessing the ProductAccess from a Browser Access from the Internet Set the Root PasswordSet Power Line Frequency Network TCP/IP AdvancedGo to Setup Events Live ViewControls on the Live View Manual TriggerAxis Media Control viewer toolbar PTZ ControlsHow to Stream H.264 Media StreamsMedia Streams Axis Media Control AMCAlternative Methods of Accessing the Video Stream Axis M1014 Network Camera Setting Up the Product Setting Up the ProductBasic Setup Video VideoVideo Stream Pixel CounterImage Stream Proﬁles264 Camera Settings Exposure SettingsView Area Image AppearanceOverlay Overlay ImageGo to Video Video Stream and select the Image tab Go to Video Overlay ImagePrivacy Mask Live View Conﬁg Default Viewer for BrowsersLive View Conﬁg User Deﬁned Links Viewer SettingsBrowser Viewer Description Preset Positions Go to PTZ Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomControl Queue AdvancedControls Detectors DetectorsCamera Tampering Motion DetectionSet Up Motion Detection Windows Motion Detection ParametersLow level 0% Default valuesRecommended values Events EventsSetting Up an Action Rule RecipientsGo to Events Action Rules and click Add RecipientSchedules RecurrencesGo to Events Recipients and click Add Go to Events Schedules and click AddRecordings RecordingsRecording List Continuous RecordingAxis M1014 Network Camera System Options System OptionsSecurity UsersIeee CertiﬁcatesBasic TCP/IP Settings Date & TimeNetwork Go to System Options Security CertiﬁcatesAdvanced TCP/IP Settings NTP Conﬁguration Host Name ConﬁgurationLink-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service FTPUPnPTM can be disabled under System Options Network UPnPTM Smtp emailUPnPTM RTP/H.264Storage BonjourSD Card Network ShareMaintenance SupportSupport Overview System OverviewReset to Factory Default Settings Logs & ReportsScripting File UploadAxis M1014 Network Camera Troubleshooting TroubleshootingEmergency Recovery Procedure Checking the FirmwareProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Problems with the H.264 format Product is accessible locally but not externallyStatus and Network indicator LEDs are ﬂashing red rapidly Video and image problems, general Video Camera SettingsProblems uploading ﬁles Storage and disk management problemsTechnical Speciﬁcations Technical SpeciﬁcationsMaintenance Installation aids PowerConnectors DimensionsPerformance Considerations M1.8