Cisco Systems CIVIS-IPC-2611 manual Preparing for Installation

Page 15

Chapter 2 Getting Started

Installing the Cisco Video Surveillance 2611 IP Dome

Preparing for Installation

Before you install the 2611 IP dome, take these actions:

•Carefully unpack the IP dome and its components.

•Run an category 5 or higher network cable to the mounting location.

•If the IP dome will not be powered from POE, run a power cable from a 12 VDC or 24 VAC power adapter to the mounting location.

Use a cable gauge that is appropriate for the distance from the IP dome to the power supply (consult a qualified electrician for more information). The terminal connectors on the IP dome support gauges from 14 AWG to 24 AWG. At the end of the wire that attaches to the IP dome, strip enough cable housing to allow each wire to be stripped to 1/4 inch (6.25 mm).

•If you will connect an external speaker, microphone, or both to the IP dome, run audio cable from each device to the mounting location.

To attach the audio cable to the IP dome, you will need the white snap on ferrite core and audio Y cable that are included in the optional audio/video cables accessory kit, which you can purchase from Cisco (Cisco part number CIVS-IPCA-1017=). Attach the white snap on ferrite core to the audio Y cable (from the optional accessory kit) at approximately 10 inches (25 cm) away from where the cable connects to the IP dome. To do so, lift the tabs to open the ferrite core, pass the cable through the ferrite core (do not loop the cable), then snap the ferrite core shut to secure it on the cable. See Figure 2-1.

Figure 2-1 Passing the Audio Cable through a Ferrite Core

•If you will use external input devices or output device that trigger alarms (connect through alarm input ports) or respond to alarms (connect through alarm output ports), run cables from each device to the mounting location. You can use up to two input devices and up to two output devices.

•Have an analog monitor available on which to view video while adjusting the field of view.

Caution Use the analog monitor only to point the IP camera to the desired field of view; do not use it to manually adjust the focus or zoom. Doing so may damage the lens. Instead, use the Focus/Zoom window in the configuration software to remotely set the focus and zoom for the IP camera.

•Have the following tools available:

–Phillips-head screwdriver

–Small flat-head screwdriver

–Cutting tool to cut a hole in a ceiling tile (required for mounting in a ceiling tile)

–Drill bits (required for surface mounting on a solid surface)

Cisco Video Surveillance 2611 IP Dome User Guide

 

OL-24128-02

2-3

 

 

 

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Americas Headquarters Cisco Video Surveillance 2611 IP Dome User GuideCisco Video Surveillance 2611 IP Dome User Guide N T E N T S Using the IP Camera with Cisco VSM A-1 Organization Preface Cisco Video Surveillance 2611 IP Dome User Guide Features, IP Camera Overview, FeaturesIP Camera Overview Physical Details, Package Contents,Top of the 2611 IP Dome Physical DetailsOverview IP Camera Overview Bottom of the 2611 IP Dome Described in the Resetting the IP Camera section onPackage Contents Before Your Begin Getting StartedPreventing Electrostatic Discharge Damage Installing the Cisco Video Surveillance 2611 IP DomePassing the Audio Cable through a Ferrite Core Preparing for InstallationRecessed Mounting in a Ceiling Tile ProcedurePlacing the 2611 IP Dome in a Ceiling Tile See -1 on Performing the Initial Setup of the IP Camera Protocol//ipaddress Accessing the IP Camera WindowsHttp//203.70.212.521024 Https//192.168.0.100Https//203.70.212.521024 Http//203.70.212.52Adjusting the Video Image Adjusting the Camera Lens on the 2611 IP Dome Powering the IP Camera On or OffInitial Setup of the IP Camera Resetting the IP CameraCleaning the IP Camera Reset Type Procedure RemarksConfiguration Overview Configuring and Managing the IP CameraConfiguration Item Explanation Guidelines for Use Reference See the Focus/Zoom Window See the Alarm I/O PortsSee the Audio Window section See the Privacy RegionSnmp Navigating the Configuration WindowsOption Description Setup WindowsBasic Setup Window Device SettingsOption Description Network Settings Advanced Setup WindowBonjour OptionOption Description QoS IP Filter WindowEapol Window EAP-TLS OptionsEAP-FAST Options Administration Windows Users Window, Maintenance Window, Firmware Window,Users Window User List AdministratorMaintenance Window Firmware Window Video Window Audio/Video WindowsSettings Dual Streams MPEG-4 + Mjpeg -Configures MPEG-4 forMPEG-4 Settings Resolution Choose the resolution of the Mjpeg video stream Mjpeg SettingsPAL/50 Hz Video AdjustmentDay/Night Vision OptionsOption Description Audio Window Controls section onDuplex Talk and Listen Full Duplex Talk and Listen Privacy Region WindowFocus/Zoom Window Choose Simplex Talk Only , Half Duplex Talk or Listen , orSecurity Windows Initialization WindowInitialization Window, Complexity Window, Users Window section on Complexity WindowMail/FTP/HTTP Window Applications WindowsSecondary Smtp Server Described in the Basic Setup Window section onMail Setup Primary Smtp ServerHttp Notification Mail BodyPrimary FTP Secondary FTPSystem-provided-name-value-pairs is the event information Motion Detection WindowEvent Window Trigger Event Event ScheduleNew Schedule Clear buttonAttachment Mail/FTP/HTTP Window section onSnmp Window Manual Control Settings Alarm I/O Ports WindowAlarm Input Settings Alarm Output SettingsStatus Windows System WindowSystem Status Audio/Video Window Audio SettingSyslog & Log Window Network WindowSys Log Server Local LogLog List Message ExplanationSystem log messages Syslog and Log Information Address FTP log messages Address1 Port1 Address2 Port2 , UserSmtp log messages Video Log WindowDelete All button Delete buttonOL-24128-02 Home Window Overview Viewing Video through the Home Window OverviewHome Window Audio controls Home Window ControlsControl Description Digital zoom controlsFor related information, see the Video Window section on Snapshot controlsSave IP camera controlsAccessing the Primary H.264 Stream Accessing Secondary H.264 StreamViewing Video through Third-Party Devices or Software Accessing Dual Streams H.264 + Mjpeg Accessing the Primary MPEG-4 StreamAccessing Dual MPEG-4 Streams Accessing the Mjpeg StreamAccessing Dual Streams MPEG-4 + Mjpeg OL-24128-02 Troubleshooting Troubleshooting For instructions, see the Video Window section on Using the IP Camera with Cisco VSMOL-24128-02 D E IN-2 IN-3 IN-4 IN-5 IN-6 IN-7 IN-8
Top Page Image Contents