Cisco Systems CIVIS-IPC-2611 manual Adjusting the Video Image

Page 22

Chapter 2 Getting Started

Adjusting the Video Image

Adjusting the Video Image

As part of the IP camera installation process, you make pan and tilt settings (and back focus settings if necessary) for the camera in the dome. If you ever need to change these settings, follow these steps:

Procedure

Step 1 Remove the IP dome assembly by twisting the dome and trim ring assembly counter-clockwise and pulling it away from the camera housing

Step 2 Remove the Privacy shield by squeezing it inward to release it from the four tabs that hold it into place. Step 3 See Figure 2-4and take these actions to adjust the camera lens to obtain the desired image:

•Temporarily attach an analog monitor to the IP dome so that you can see video while adjusting the camera. If the cable from the monitor terminates with a 3.5 mm jack, plug it into the analog video output port on the IP dome. If the cable terminates with a BNC connector, connect it to the mini cable with BNC adapter, then plug the cable into the analog video output port. The mini cable with BNC adapter is included in the audio/video cables accessory kit, which you can purchase from Cisco (Cisco part number CIVS-IPCA-1017=).

•Make the following adjustments, viewing the video on the analog monitor as needed:

–Rotation—The rotation is factory set and should not require adjustments. In the event that it does need to be adjusted, turn the notched rotation wheel until you achieve the desired image.

–Pan—Use a Phillips-head to loosen the panning lock screw (the one slightly recessed in a cutout), then rotate the camera to obtain the desired image, then tighten the panning lock screw.

–Tilt—Loosen the two tilt lock screws, adjust the lens to obtain the desired image, then tighten the screws.

–Back focus—The back focus is factory set for optimal use and should not require adjustments. In the event that it does need to be adjusted, use the 0.9 mm Allen wrench that is supplied with the IP camera to loosen the back focus hex screw, then adjust the back focus by aiming the IP camera at an object that is at least 15 feet (4.5 meters) away and gently sliding the lens toward or away from the camera. Take care not to pull the lens completely away from the camera.Obtain a sharp picture in both wide-angle and telephoto positions. When the focus is set as desired, use the Allen wrench to tighten the back focus hex screw.

Caution Do not manually adjust the focus or zoom for the IP camera. Attempting to manually do so may damage the IP camera lens. Instead, use the Focus/Zoom window in the configuration software to remotely set the focus and zoom for the IP camera.

 

Cisco Video Surveillance 2611 IP Dome User Guide

2-10

OL-24128-02

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Cisco Video Surveillance 2611 IP Dome User Guide Americas HeadquartersCisco Video Surveillance 2611 IP Dome User Guide N T E N T S Using the IP Camera with Cisco VSM A-1 Organization Preface Cisco Video Surveillance 2611 IP Dome User Guide Features Features, IP Camera Overview,Physical Details, Package Contents, IP Camera OverviewPhysical Details Top of the 2611 IP DomeOverview IP Camera Overview Described in the Resetting the IP Camera section on Bottom of the 2611 IP DomePackage Contents Getting Started Before Your BeginInstalling the Cisco Video Surveillance 2611 IP Dome Preventing Electrostatic Discharge DamagePreparing for Installation Passing the Audio Cable through a Ferrite CoreProcedure Recessed Mounting in a Ceiling TilePlacing the 2611 IP Dome in a Ceiling Tile See -1 on Performing the Initial Setup of the IP Camera Accessing the IP Camera Windows Protocol//ipaddressHttp//203.70.212.52 Https//192.168.0.100Https//203.70.212.521024 Http//203.70.212.521024Adjusting the Video Image Powering the IP Camera On or Off Adjusting the Camera Lens on the 2611 IP DomeReset Type Procedure Remarks Resetting the IP CameraCleaning the IP Camera Initial Setup of the IP CameraConfiguring and Managing the IP Camera Configuration OverviewConfiguration Item Explanation Guidelines for Use Reference See the Privacy Region See the Alarm I/O PortsSee the Audio Window section See the Focus/Zoom WindowNavigating the Configuration Windows SnmpDevice Settings Setup WindowsBasic Setup Window Option DescriptionOption Description Advanced Setup Window Network SettingsOption BonjourOption Description IP Filter Window QoSEAP-TLS Options Eapol WindowEAP-FAST Options Users Window, Maintenance Window, Firmware Window, Administration WindowsUsers Window Administrator User ListMaintenance Window Firmware Window Audio/Video Windows Video WindowDual Streams MPEG-4 + Mjpeg -Configures MPEG-4 for SettingsMPEG-4 Settings Mjpeg Settings Resolution Choose the resolution of the Mjpeg video streamVideo Adjustment PAL/50 HzOptions Day/Night VisionOption Description Controls section on Audio WindowDuplex Talk and Listen Choose Simplex Talk Only , Half Duplex Talk or Listen , or Privacy Region WindowFocus/Zoom Window Full Duplex Talk and ListenInitialization Window Security WindowsInitialization Window, Complexity Window, Complexity Window Users Window section onApplications Windows Mail/FTP/HTTP WindowPrimary Smtp Server Described in the Basic Setup Window section onMail Setup Secondary Smtp ServerSecondary FTP Mail BodyPrimary FTP Http NotificationMotion Detection Window System-provided-name-value-pairs is the event informationEvent Window Clear button Event ScheduleNew Schedule Trigger EventMail/FTP/HTTP Window section on AttachmentSnmp Window Alarm Output Settings Alarm I/O Ports WindowAlarm Input Settings Manual Control SettingsSystem Window Status WindowsSystem Status Audio Setting Audio/Video WindowNetwork Window Syslog & Log WindowLocal Log Sys Log ServerMessage Explanation Log ListSystem log messages Syslog and Log Information Address Address1 Port1 Address2 Port2 , User FTP log messagesVideo Log Window Smtp log messagesDelete button Delete All buttonOL-24128-02 Viewing Video through the Home Window Overview Home Window OverviewHome Window Digital zoom controls Home Window ControlsControl Description Audio controlsIP camera controls Snapshot controlsSave For related information, see the Video Window section onAccessing Secondary H.264 Stream Accessing the Primary H.264 StreamViewing Video through Third-Party Devices or Software Accessing the Mjpeg Stream Accessing the Primary MPEG-4 StreamAccessing Dual MPEG-4 Streams Accessing Dual Streams H.264 + MjpegAccessing Dual Streams MPEG-4 + Mjpeg OL-24128-02 Troubleshooting Troubleshooting Using the IP Camera with Cisco VSM For instructions, see the Video Window section onOL-24128-02 D E IN-2 IN-3 IN-4 IN-5 IN-6 IN-7 IN-8
Top Page Image Contents