Cisco Systems CIVIS-IPC-2611 manual Event Window

Page 55

Chapter 3 Configuring and Managing the IP Camera

Applications Windows

Table 3-16

Motion Detection Window Options

 

 

 

Option

 

Description

 

 

Motion Detection Area

• Motion Inclusion Regions—Create a window to designate an area to

 

 

examine for motion. Select up to 4 check boxes to specify areas in the

 

 

video. If desired, enter a name of up to 12 characters for each area in the

 

 

field next to the corresponding check box. Drag the window to the

 

 

desired area and drag an edge or corner of the window to resize it.

 

 

To remove a window, uncheck the associated check box.

 

 

• Motion Exclusion Regions—Create a window to designate an area to

 

 

ignore for motion. Select up to 4 check boxes to specify areas in the

 

 

video. If desired, enter a name of up to 12 characters for each area in the

 

 

field next to the corresponding check box. Drag the window to the

 

 

desired area and drag an edge or corner of the window to resize it.

 

 

To remove a window, uncheck the associated check box.

 

 

• Motion Detection Parameters—Each Motion Detection Inclusion

 

 

Region has its unique set of Motion Detection Parameters. Click on a

 

 

defined Motion Inclusion Region to examine or edit its Motion

 

 

Detection Parameters for that specific window:

 

 

– Sensitivity—Designates the relative change in luminance that the

 

 

camera must detect for motion detection. A lower value means that

 

 

more change is required for motion detection.

 

 

– Threshold—Designates the percentage of the motion inclusion

 

 

region that the camera must detect motion to generate an alert. The

 

 

camera detects motion using the defined sensitivity level.

 

 

– Activity Level—Display only. Horizontal bar that represents how

 

 

much activity is being detected in the area. Test and adjust the

 

 

sensitivity by looking at this indicator.

 

 

 

Event Window

The Event window provides options for configuring how the IP camera handles events. An event is either of the following:

•Motion that the IP camera detects. For related information about motion detection, see the “Motion Detection Window” section on page 3-30.

•A change of state from low to high or from high to low on an input port of the IP camera. For related information about input ports, see the “Alarm I/O Ports Window” section on page 3-35.

When an event occurs, it triggers the IP camera to take certain configured actions. For example, an event can cause the IP camera to send a notification e-mail message to designated recipients and upload a video file to an SMTP server or an FTP server, or it can cause the IP camera to activate an output port.

The Event window allows you to designate up to 10 schedules. If an event takes place within a designated schedule, the IP camera takes the actions that you configure.

To display the Event window, access the configuration windows as described in the “Accessing the IP Camera Windows” section on page 2-8, click Applications, then click Event.

 

 

Cisco Video Surveillance 2611 IP Dome User Guide

 

 

 

 

 

 

OL-24128-02

 

 

3-31

 

 

 

 

 

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Americas Headquarters Cisco Video Surveillance 2611 IP Dome User GuideCisco Video Surveillance 2611 IP Dome User Guide N T E N T S Using the IP Camera with Cisco VSM A-1 Organization Preface Cisco Video Surveillance 2611 IP Dome User Guide Features, IP Camera Overview, FeaturesIP Camera Overview Physical Details, Package Contents,Top of the 2611 IP Dome Physical DetailsOverview IP Camera Overview Bottom of the 2611 IP Dome Described in the Resetting the IP Camera section onPackage Contents Before Your Begin Getting StartedPreventing Electrostatic Discharge Damage Installing the Cisco Video Surveillance 2611 IP DomePassing the Audio Cable through a Ferrite Core Preparing for InstallationRecessed Mounting in a Ceiling Tile ProcedurePlacing the 2611 IP Dome in a Ceiling Tile See -1 on Performing the Initial Setup of the IP Camera Protocol//ipaddress Accessing the IP Camera WindowsHttp//203.70.212.521024 Https//192.168.0.100Https//203.70.212.521024 Http//203.70.212.52Adjusting the Video Image Adjusting the Camera Lens on the 2611 IP Dome Powering the IP Camera On or OffInitial Setup of the IP Camera Resetting the IP CameraCleaning the IP Camera Reset Type Procedure RemarksConfiguration Overview Configuring and Managing the IP CameraConfiguration Item Explanation Guidelines for Use Reference See the Focus/Zoom Window See the Alarm I/O PortsSee the Audio Window section See the Privacy RegionSnmp Navigating the Configuration WindowsOption Description Setup WindowsBasic Setup Window Device SettingsOption Description Network Settings Advanced Setup WindowBonjour OptionOption Description QoS IP Filter WindowEAP-TLS Options Eapol WindowEAP-FAST Options Users Window, Maintenance Window, Firmware Window, Administration WindowsUsers Window User List AdministratorMaintenance Window Firmware Window Video Window Audio/Video WindowsSettings Dual Streams MPEG-4 + Mjpeg -Configures MPEG-4 forMPEG-4 Settings Resolution Choose the resolution of the Mjpeg video stream Mjpeg SettingsPAL/50 Hz Video AdjustmentDay/Night Vision OptionsOption Description Controls section on Audio WindowDuplex Talk and Listen Full Duplex Talk and Listen Privacy Region WindowFocus/Zoom Window Choose Simplex Talk Only , Half Duplex Talk or Listen , orInitialization Window Security WindowsInitialization Window, Complexity Window, Users Window section on Complexity WindowMail/FTP/HTTP Window Applications WindowsSecondary Smtp Server Described in the Basic Setup Window section onMail Setup Primary Smtp ServerHttp Notification Mail BodyPrimary FTP Secondary FTPSystem-provided-name-value-pairs is the event information Motion Detection WindowEvent Window Trigger Event Event ScheduleNew Schedule Clear buttonAttachment Mail/FTP/HTTP Window section onSnmp Window Manual Control Settings Alarm I/O Ports WindowAlarm Input Settings Alarm Output SettingsSystem Window Status WindowsSystem Status Audio/Video Window Audio SettingSyslog & Log Window Network WindowSys Log Server Local LogMessage Explanation Log ListSystem log messages Syslog and Log Information Address FTP log messages Address1 Port1 Address2 Port2 , UserSmtp log messages Video Log WindowDelete All button Delete buttonOL-24128-02 Home Window Overview Viewing Video through the Home Window OverviewHome Window Audio controls Home Window ControlsControl Description Digital zoom controlsFor related information, see the Video Window section on Snapshot controlsSave IP camera controlsAccessing Secondary H.264 Stream Accessing the Primary H.264 StreamViewing Video through Third-Party Devices or Software Accessing Dual Streams H.264 + Mjpeg Accessing the Primary MPEG-4 StreamAccessing Dual MPEG-4 Streams Accessing the Mjpeg StreamAccessing Dual Streams MPEG-4 + Mjpeg OL-24128-02 Troubleshooting Troubleshooting For instructions, see the Video Window section on Using the IP Camera with Cisco VSMOL-24128-02 D E IN-2 IN-3 IN-4 IN-5 IN-6 IN-7 IN-8
Top Page Image Contents