NEC RS-232C manual Operation Code OP code Table, Dicom SIM

Page 26

6.3. Operation Code (OP code) Table

PICTURE

Item			OP	OP code	Parameter	Remarks
			cod
			e
			pag
Backlight			e	10h	0: dark
Backlight			00h	10h	0: dark

					100(64h): bright
Contrast			00h	12h	0: low

					100(64h): high
Sharpness			00h	8Ch	0: dull

					24(18h): sharp
Brightness			00h	92h	0: dark

					100(64h): bright
Hue			00h	90h	0: purplish

					100(64h): greenish
Color			02h	1Fh	0: pale

					100(64h): deep
Color Temperature			00h	54h	0:2600K	100K/step

					74(4Ah):10000K
Color control			00h	Red: 9Bh	0:
				Yellow:
				9Ch	100(64h):(center)
				Green:
				9Dh	200(C8h):
				Cyan:
				9Eh
				Blue:
				9Fh
				Magenta:
				A0h
Gamma Correction			02h	68h	Gamma
					Table Selection
					1: Native Gamma
					4: Gamma=2.2
					8: Gamma=2.4
					7: S Gamma
					5: DICOM SIM.
					6: Programmable
Movie		Adaptive	02h	8Dh	0: None
Settings		Contrast			1: Off
					2: Low
					3: Middle
					4: High
		Noise	02h	26h	0: Off	Page02-20		also
		Reduction				works as same.
					5: High
		Telecine	02h	23h	1: Off
					2: Auto
Picture mode			02h	1Ah	1: sRGB	sRGB:
					3: Hi-Bright	PC mode only
					4: Standard	Cinema:
					5: Cinema	A/V mode only
					6: ISF-Day	ISF-Day:
					7: ISF-Night	ISF-Day:
					11(0Bh): Ambient-1	ISF-Night:		an
					12(0Ch): Ambient-2	Each	needs	an
						adjustment by ISF.

(26/72)

Image 26

Contents External Control 10.1 Application LAN control II. Preparation Connectors and wiringRS-232C Remote control Communication timing AsciiCommunication Format Get Parameter Reply MonitorHeader block format fixed length ALLPage ETX Message block formatSTX MSB LSB10/72 Check code SOHDelimiter Message type Get current Parameter from a monitor00h No Error Get parameter replySet parameter ETX MSB LSBSet parameter reply Current conditionCommands Save Current Settings Send 0730h, 37h as Get Timing Report command Get Timing Report and Timing replyNull Message BCC IV. Control Commands Typical procedure exampleHow to change the Backlight setting Message Check code Delimiter Header Message Check code Delimiter SOH-0-Monitor ID-0-E-0-A STX-0-2-7-8-0-0-0-1-ETX SOH-0-Monitor ID-0-C-0-6 STX-0-2-7-9-ETX Readout value is 2s complement Operation Code OP code Table Dicom SIMPosition 00h 20h Left side OP code Parameter Remarks Cod Pag Input Resolution DAh Surround HdmiRGB/HV PIPOSD 02h 7Dh None Scart DVI-PCDVI-HD IP ON/PROGRESSIVE‘SURROUND’ Mute Unmute Screen MuteScreen Mute on Screen Mute OFF MTS PIP ON/OFFOP code Parameter Remarks Cod Pag PIP Input 02h 73h No mean Power control procedure Power status readCR 0Dh End of packet 37/72 Power control Controller requests the monitor to control monitor powerDelimiter CR 0Dh End of packet 39/72 Asset Data read and write Asset Data Read Request and replyDelimiter CR 0Dh End of packet 41/72 Asset Data write CR 0Dh End of packet 43/72 BCC DS-ETX Date & Time read and writeDate & Time Read MN Minutes 0-030h, 30h Date & Time Write Check code Delimiter Delimiter CR 0Dh End of packet 48/72 Schedule read and write Schedule ReadB33h, 42h C33h, 43h On timer isnt set Page BCC OFF HOUR-OFF MIN-INPUT-WD-FL-ETX B33h, 42h 59 =3Bh C33h, 43h Off timer isn’t set PG-ON HOURS-ON MIN-OFF HOURS-OFF MIN-INPUT-WD-FL-P Mode Schedule WritePage BCC OFF HOUR-OFF MIN-INPUT-WD-FL-P Mode 57/72 SOH-0-Monitor ID-0-A-0-A STX-C-2-1-5-PG-EN-ETX Delimiter CR 0Dh End of packet 59/72 STX-C-2-1-4-PG-ON HOUR-ON MIN SOH-0-0-Monitor ID-B-1-8 STX-C-3-1-4-ST-PG-ON HOUR-ON MIN 030h, 30h 731h, 37h 23 =17h 831h, 38h Off timer isnt set SOH-0-0-Monitor ID-B-0-C STX-C-3-1-5-ST-PG-EN-ETX Self diagnosis Self-diagnosis status readPage Serial No. & Model Name Read Serial No. ReadModel Name Read Security Lock Security Lock ControlSTX-C-3-1-D-ST-EN-ETX Direct TV Chanel Read & Write Direct TV Chanel Read & ReplyDirect TV Chanel Write & Reply All data are subject to change without notice

Related manuals

Manual 50 pages 13.24 Kb