NEC RS-232C manual Rgb/Hv, Pip

Page 30

	Item		OP	OP code	Parameter		Remarks
			cod
			e
			pag
			e
	PIP H Position		02h	74h	0: left

					100(64h): right
	PIP V Position		02h	75h	0: top

					100(64h): bottom
	Aspect		10h	83h	0: No operate
					1: Normal
					2: Full
					3: Wide
					4: (reserved)
					5: (reserved)
	Text	Mode	10h	08h	0: None
	Ticker				1: Off
					2: Horizontal
					3: Vertical
		Position	10h	09h	0: Top/Left

					100: Bottom/Right
		Size	10h	0Ah	0-1: Do not set.
					2: Narrow(2/24)

					8: Wide(8/24)
		Blend	10h	0Bh	1: 10%
						100%
					10:	100%
		Detect	10h	0Ch	0: None
					1: Auto
					2: Off
		Fade In	10h	0Dh	0: None
					1: On
					2: Off
	PIP Input(Sub input)		02h	73h	0: No mean		This operation	has
					1: VGA		limitation	of
					2: RGB/HV		selection. Please
					3: DVI		refer to the monitor
					4: HDMI (Set only)		instruction
					5: Video1		manual.
					6: Video2
					7: S-Video
					12(0Ch): DVD/HD1
					13(0Dh): Option
					14(0Eh): DVD/HD2
					15(0Fh): Display
						Port
					17(11h): HDMI
	Menu tree reset		02h	CBh	0: None		Momentary
	(PIP)				6: Reset PIP
						category
	Language		00h	68h	1: English		OSD Language
					2: German
					3: French
					4: Spanish
					5: Japanese
OSD					6: Italian
					7: Swedish
					9: Russian
					9: Russian
					14(0Eh): Chinese
	Menu Display Time		00h	FCh	0-1: Do not set.		5sec/step
					2:	10s
					3:	15s
						240s
					48:	240s

(30/72)

Image 30

Contents External Control 10.1 Application II. Preparation Connectors and wiring RS-232C Remote controlLAN control Communication timing AsciiCommunication Format Get Parameter Reply MonitorHeader block format fixed length ALLPage ETX Message block formatSTX MSB LSB10/72 Check code SOHDelimiter Message type Get current Parameter from a monitor00h No Error Get parameter replySet parameter ETX MSB LSBSet parameter reply Current conditionCommands Save Current Settings Send 0730h, 37h as Get Timing Report command Get Timing Report and Timing replyNull Message IV. Control Commands Typical procedure example How to change the Backlight settingBCC Message Check code Delimiter Header Message Check code Delimiter SOH-0-Monitor ID-0-E-0-A STX-0-2-7-8-0-0-0-1-ETX SOH-0-Monitor ID-0-C-0-6 STX-0-2-7-9-ETX Readout value is 2s complement Operation Code OP code Table Dicom SIMPosition 00h 20h Left side OP code Parameter Remarks Cod Pag Input Resolution DAh Surround HdmiRGB/HV PIPOSD 02h 7Dh None Scart DVI-PCDVI-HD IP ON/PROGRESSIVE‘SURROUND’ Mute Unmute Screen MuteScreen Mute on Screen Mute OFF MTS PIP ON/OFFOP code Parameter Remarks Cod Pag PIP Input 02h 73h No mean Power control procedure Power status readCR 0Dh End of packet 37/72 Power control Controller requests the monitor to control monitor powerDelimiter CR 0Dh End of packet 39/72 Asset Data read and write Asset Data Read Request and replyDelimiter CR 0Dh End of packet 41/72 Asset Data write CR 0Dh End of packet 43/72 Date & Time read and write Date & Time ReadBCC DS-ETX MN Minutes 0-030h, 30h Date & Time Write Check code Delimiter Delimiter CR 0Dh End of packet 48/72 Schedule read and write Schedule ReadB33h, 42h C33h, 43h On timer isnt set Page BCC OFF HOUR-OFF MIN-INPUT-WD-FL-ETX B33h, 42h 59 =3Bh C33h, 43h Off timer isn’t set PG-ON HOURS-ON MIN-OFF HOURS-OFF MIN-INPUT-WD-FL-P Mode Schedule WritePage BCC OFF HOUR-OFF MIN-INPUT-WD-FL-P Mode 57/72 SOH-0-Monitor ID-0-A-0-A STX-C-2-1-5-PG-EN-ETX Delimiter CR 0Dh End of packet 59/72 STX-C-2-1-4-PG-ON HOUR-ON MIN SOH-0-0-Monitor ID-B-1-8 STX-C-3-1-4-ST-PG-ON HOUR-ON MIN 030h, 30h 731h, 37h 23 =17h 831h, 38h Off timer isnt set SOH-0-0-Monitor ID-B-0-C STX-C-3-1-5-ST-PG-EN-ETX Self diagnosis Self-diagnosis status readPage Serial No. & Model Name Read Serial No. ReadModel Name Read Security Lock Security Lock ControlSTX-C-3-1-D-ST-EN-ETX Direct TV Chanel Read & Write Direct TV Chanel Read & ReplyDirect TV Chanel Write & Reply All data are subject to change without notice

Related manuals

Manual 50 pages 13.24 Kb