NEC RS-232C manual OP code Parameter Remarks Cod Pag PIP Input 02h 73h No mean

Page 35

	Item		OP	OP code	Parameter				Remarks
			cod
			e
			pag
			e
	PIP Input		02h	73h	0: No mean				This operation has
					1: VGA				limitation		of
					2: RGB/HV				selection.		Please
					3: DVI				refer to the monitor
					4: HDMI (Set only)				instruction
					5: Video1				manual.
					6: Video2
					7: S-Video
					12(0Ch): DVD/HD1
					13(0Dh): Option
					14(0Eh): DVD/HD2
					15(0Fh): Display
					Port
					17(11h): HDMI
	Still Capture		02h	76h	0: Off				Momentary
					1: Capture
	Signal Information		02h	EAh	0: No Action
					1: Off
					(No indication)
					2: On
					(Indication）
	Auto Setup		00h	1Eh	1: Execute				Momentary
	TV-Channel UP/DOWN		00h	8Bh	0: No Action				This	operation
					1: Up				requires	supported
					2: Down				option TV tuner.
Temperature sensor	Select	Temperature	02h	78h	1: Sensor #1
	sensor				2: Sensor #2
					3: Sensor #3
	Readout a temperature		02h	79h	Returned	value	is	2's	Read only
					complement.
					Refer to section 6.2
	Readout	carbon	10h	10h	0:				Read only
footprint	footprint
	(g)				999:
	Readout	carbon	10h	11h	0:				Read only
	footprint
	(kg)				65535:
	Readout carbon Usage		10h	26h	0:				Read only
Carbon	Readout carbon Usage		10h	26h	0:				Read only
	(g)
					999:
	Readout carbon Usage		10h	27h	0:				Read only
	Readout carbon Usage		10h	27h	0:				Read only
	(kg)
					65535:

(35/72)

Image 35

Contents External Control 10.1 Application LAN control II. Preparation Connectors and wiringRS-232C Remote control Ascii Communication timingGet Parameter Reply Monitor Communication FormatALL Header block format fixed lengthPage MSB LSB Message block formatSTX ETX10/72 SOH Check codeDelimiter Get current Parameter from a monitor Message typeGet parameter reply 00h No ErrorETX MSB LSB Set parameterCurrent condition Set parameter replySave Current Settings CommandsGet Timing Report and Timing reply  Send 0730h, 37h as Get Timing Report commandNull Message BCC IV. Control Commands Typical procedure exampleHow to change the Backlight setting Message Check code Delimiter Header Message Check code Delimiter SOH-0-Monitor ID-0-E-0-A STX-0-2-7-8-0-0-0-1-ETX SOH-0-Monitor ID-0-C-0-6 STX-0-2-7-9-ETX Readout value is 2s complement Dicom SIM Operation Code OP code TablePosition 00h 20h Left side OP code Parameter Remarks Cod Pag Input Resolution DAh Hdmi SurroundPIP RGB/HVOSD 02h 7Dh None IP ON/PROGRESSIVE DVI-PCDVI-HD ScartPIP ON/OFF Mute Unmute Screen MuteScreen Mute on Screen Mute OFF MTS ‘SURROUND’OP code Parameter Remarks Cod Pag PIP Input 02h 73h No mean Power status read Power control procedureCR 0Dh End of packet 37/72 Controller requests the monitor to control monitor power Power controlDelimiter CR 0Dh End of packet 39/72 Asset Data Read Request and reply Asset Data read and writeDelimiter CR 0Dh End of packet 41/72 Asset Data write CR 0Dh End of packet 43/72 BCC DS-ETX Date & Time read and writeDate & Time Read MN Minutes 0-030h, 30h Date & Time Write Check code Delimiter Delimiter CR 0Dh End of packet 48/72 Schedule Read Schedule read and writeB33h, 42h C33h, 43h On timer isnt set Page BCC OFF HOUR-OFF MIN-INPUT-WD-FL-ETX B33h, 42h 59 =3Bh C33h, 43h Off timer isn’t set Schedule Write PG-ON HOURS-ON MIN-OFF HOURS-OFF MIN-INPUT-WD-FL-P ModePage BCC OFF HOUR-OFF MIN-INPUT-WD-FL-P Mode 57/72 SOH-0-Monitor ID-0-A-0-A STX-C-2-1-5-PG-EN-ETX Delimiter CR 0Dh End of packet 59/72 STX-C-2-1-4-PG-ON HOUR-ON MIN SOH-0-0-Monitor ID-B-1-8 STX-C-3-1-4-ST-PG-ON HOUR-ON MIN 030h, 30h 731h, 37h 23 =17h 831h, 38h Off timer isnt set SOH-0-0-Monitor ID-B-0-C STX-C-3-1-5-ST-PG-EN-ETX Self-diagnosis status read Self diagnosisPage Serial No. Read Serial No. & Model Name ReadModel Name Read Security Lock Control Security LockSTX-C-3-1-D-ST-EN-ETX Direct TV Chanel Read & Reply Direct TV Chanel Read & WriteDirect TV Chanel Write & Reply All data are subject to change without notice

Related manuals

Manual 50 pages 13.24 Kb