NEC RS-232C manual Position 00h 20h Left side

Page 27

	Item			OP	OP code	Parameter	Remarks
				cod
				e
				pag
				e
	Ambient		Ambient	10h	33h	0: dark
			Brightness
			Low			100(64h): bright
			Ambient	10h	34h	0: dark
			Brightness
			High			100(64h): bright
			Get Current	02h	B4h	0:	Read only
			Illuminanc
			e			Max.

			Bright	02h	B5h	0:	Read only
			Sensor Read
						255(FFh)
	Menu tree	reset		02h	CBh	0: None	Momentary
	(Picture)					2: Reset
						Picture category

	Auto Setup			00h	1Eh	1: Execute	Momentary
	Auto Adjust					N/A
	H Position			00h	20h	0: Left side	Depends on a display
							timing
						Max.: Right side
	V Position			00h	30h	0: Bottom side	Depends on a display
							timing
ADJUST						Max.: Top side
	Clock			00h	0Eh	0:

						Max. :
	Phase			00h	3Eh	0:

						Max. :
	H Resolution			02h	50h	0: Low

						Max. : High
	V Resolution			02h	51h	0: Low

						Max.: High

(27/72)

Image 27

Contents External Control 10.1 Application II. Preparation Connectors and wiring RS-232C Remote controlLAN control Ascii Communication timingGet Parameter Reply Monitor Communication FormatALL Header block format fixed lengthPage MSB LSB Message block formatSTX ETX10/72 SOH Check codeDelimiter Get current Parameter from a monitor Message typeGet parameter reply 00h No ErrorETX MSB LSB Set parameterCurrent condition Set parameter replySave Current Settings CommandsGet Timing Report and Timing reply  Send 0730h, 37h as Get Timing Report commandNull Message IV. Control Commands Typical procedure example How to change the Backlight settingBCC Message Check code Delimiter Header Message Check code Delimiter SOH-0-Monitor ID-0-E-0-A STX-0-2-7-8-0-0-0-1-ETX SOH-0-Monitor ID-0-C-0-6 STX-0-2-7-9-ETX Readout value is 2s complement Dicom SIM Operation Code OP code TablePosition 00h 20h Left side OP code Parameter Remarks Cod Pag Input Resolution DAh Hdmi SurroundPIP RGB/HVOSD 02h 7Dh None IP ON/PROGRESSIVE DVI-PCDVI-HD ScartPIP ON/OFF Mute Unmute Screen MuteScreen Mute on Screen Mute OFF MTS ‘SURROUND’OP code Parameter Remarks Cod Pag PIP Input 02h 73h No mean Power status read Power control procedureCR 0Dh End of packet 37/72 Controller requests the monitor to control monitor power Power controlDelimiter CR 0Dh End of packet 39/72 Asset Data Read Request and reply Asset Data read and writeDelimiter CR 0Dh End of packet 41/72 Asset Data write CR 0Dh End of packet 43/72 Date & Time read and write Date & Time ReadBCC DS-ETX MN Minutes 0-030h, 30h Date & Time Write Check code Delimiter Delimiter CR 0Dh End of packet 48/72 Schedule Read Schedule read and writeB33h, 42h C33h, 43h On timer isnt set Page BCC OFF HOUR-OFF MIN-INPUT-WD-FL-ETX B33h, 42h 59 =3Bh C33h, 43h Off timer isn’t set Schedule Write PG-ON HOURS-ON MIN-OFF HOURS-OFF MIN-INPUT-WD-FL-P ModePage BCC OFF HOUR-OFF MIN-INPUT-WD-FL-P Mode 57/72 SOH-0-Monitor ID-0-A-0-A STX-C-2-1-5-PG-EN-ETX Delimiter CR 0Dh End of packet 59/72 STX-C-2-1-4-PG-ON HOUR-ON MIN SOH-0-0-Monitor ID-B-1-8 STX-C-3-1-4-ST-PG-ON HOUR-ON MIN 030h, 30h 731h, 37h 23 =17h 831h, 38h Off timer isnt set SOH-0-0-Monitor ID-B-0-C STX-C-3-1-5-ST-PG-EN-ETX Self-diagnosis status read Self diagnosisPage Serial No. Read Serial No. & Model Name ReadModel Name Read Security Lock Control Security LockSTX-C-3-1-D-ST-EN-ETX Direct TV Chanel Read & Reply Direct TV Chanel Read & WriteDirect TV Chanel Write & Reply All data are subject to change without notice

Related manuals

Manual 50 pages 13.24 Kb