NEC RS-232C manual OP code Parameter Remarks Cod Pag Input Resolution DAh

Page 28

AUDIO

Item		OP	OP code	Parameter	Remarks
		cod
		e
		pag
Input Resolution		e	DAh	Input Resolution select
Input Resolution		02h	DAh	Input Resolution select
				0:no mean
				1:Item 1(always Auto)
				2:Item 2
				3:Item 3
				4:Item 4
				5:Item 5
				Over5:Ignore
				Ex)
				Item 1= AUTO
				Item 2= -- /
				1024x768 /
				1400x1050 /
				800x600 /
				1280x960
				Item 3= -- /
				1280x768 /
				1680x1050 /
				1024x576 /
				1600x900 /
				Item 4= -- /
				1360x768 /
				-- /
				-- /
				--
				Item 5= -- /
				1366x768
				-- /
				-- /
				--
Aspect		02h	70h	0: No operate	Wide:
				1: Normal	Dynamic
				2: Full	A/V mode only
				3: Wide
				4: Zoom
				5: (reserved)
				6: Dynamic
				7: Off (dot by dot)
Zoom	Zoom	02h	6Fh	1:100％
Control				2:101％

				201:300％
	Zoom	02h	6Ch	1:100％
	H-Expansion			2:101％

				201:300％
	Zoom	02h	6Dh	1:100％
	V-Expansion			2:101％

				201:300％
	Zoom	02h	CCh	0: Left side
	H-Position
				Max.: Right side
	Zoom	02h	CDh	0: Down side
	V-Position
				Max.: Up side
Menu tree	reset	02h	CBh	0: None	Momentary
(Adjust)				3: Reset
Volume		00h	62h	Adjust category	00h
Volume		00h	62h	0: whisper	00h

				100: loud

(28/72)

Image 28

Contents External Control 10.1 Application RS-232C Remote control II. Preparation Connectors and wiringLAN control Communication timing AsciiCommunication Format Get Parameter Reply MonitorHeader block format fixed length ALLPage Message block format STXETX MSB LSB10/72 Check code SOHDelimiter Message type Get current Parameter from a monitor00h No Error Get parameter replySet parameter ETX MSB LSBSet parameter reply Current conditionCommands Save Current Settings Send 0730h, 37h as Get Timing Report command Get Timing Report and Timing replyNull Message How to change the Backlight setting IV. Control Commands Typical procedure exampleBCC Message Check code Delimiter Header Message Check code Delimiter SOH-0-Monitor ID-0-E-0-A STX-0-2-7-8-0-0-0-1-ETX SOH-0-Monitor ID-0-C-0-6 STX-0-2-7-9-ETX Readout value is 2s complement Operation Code OP code Table Dicom SIMPosition 00h 20h Left side OP code Parameter Remarks Cod Pag Input Resolution DAh Surround HdmiRGB/HV PIPOSD 02h 7Dh None DVI-PC DVI-HDScart IP ON/PROGRESSIVEMute Unmute Screen Mute Screen Mute on Screen Mute OFF MTS‘SURROUND’ PIP ON/OFFOP code Parameter Remarks Cod Pag PIP Input 02h 73h No mean Power control procedure Power status readCR 0Dh End of packet 37/72 Power control Controller requests the monitor to control monitor powerDelimiter CR 0Dh End of packet 39/72 Asset Data read and write Asset Data Read Request and replyDelimiter CR 0Dh End of packet 41/72 Asset Data write CR 0Dh End of packet 43/72 Date & Time Read Date & Time read and writeBCC DS-ETX MN Minutes 0-030h, 30h Date & Time Write Check code Delimiter Delimiter CR 0Dh End of packet 48/72 Schedule read and write Schedule ReadB33h, 42h C33h, 43h On timer isnt set Page BCC OFF HOUR-OFF MIN-INPUT-WD-FL-ETX B33h, 42h 59 =3Bh C33h, 43h Off timer isn’t set PG-ON HOURS-ON MIN-OFF HOURS-OFF MIN-INPUT-WD-FL-P Mode Schedule WritePage BCC OFF HOUR-OFF MIN-INPUT-WD-FL-P Mode 57/72 SOH-0-Monitor ID-0-A-0-A STX-C-2-1-5-PG-EN-ETX Delimiter CR 0Dh End of packet 59/72 STX-C-2-1-4-PG-ON HOUR-ON MIN SOH-0-0-Monitor ID-B-1-8 STX-C-3-1-4-ST-PG-ON HOUR-ON MIN 030h, 30h 731h, 37h 23 =17h 831h, 38h Off timer isnt set SOH-0-0-Monitor ID-B-0-C STX-C-3-1-5-ST-PG-EN-ETX Self diagnosis Self-diagnosis status readPage Serial No. & Model Name Read Serial No. ReadModel Name Read Security Lock Security Lock ControlSTX-C-3-1-D-ST-EN-ETX Direct TV Chanel Read & Write Direct TV Chanel Read & ReplyDirect TV Chanel Write & Reply All data are subject to change without notice

Related manuals

Manual 50 pages 13.24 Kb