Sennheiser EMP 2015 manual Getting ready, Setting up the EMP, Inserting and replacing the battery

Page 42

6 Getting ready

EMP 2015 receiver/amplifier combination

Setting up the EMP 2015

The EMP 2015 is equipped with a temperature-controlled ventilation system. To ensure sufficient ventilation, please make sure that the ventilation apertures at the side panels are not covered. An integrated temperature monitoring device protects the EMP 2015 against overheating by turning it off if the temperature rises above a certain value. After sufficient cooling, the EMP 2015 is automatically turned on again.

Connecting the antenna and preparing the mains connection
Antenna
Connect the supplied telescopic antenna to the BNC socket	at the
rear of the EMP 2015 and lock the bayonet catch.

Pull out the antenna and align it.

Note:

For optimum reception, align the transmitting and receiving antenna vertically.

Mains connection

Plug the power cord into socket

at the rear of the EMP 2015.

SK 500 bodypack transmitter

Inserting and replacing the battery
Slide the cover of the battery compartment	in the direction of the
embossed arrow until it clicks audibly.

Open the cover.

Insert the 9 V PP3 battery (IEC 6 LR 61). Please observe correct polarity when inserting the battery.

Close the battery compartment.

To remove the battery, push the red lever	in the battery compartment
towards the bottom side of the transmitter.

Note:

If powered by a standard PP3 battery, the operating time of the transmitter is approx. 6 hours. If powered by a rechargeable battery, the operating time is approx. 4 hours. Special note on rechargeable battery operation: For optimum operation, only use 9.6 V / 160 mAh NiMH batteries.

44

Image 42

Contents Soundfield System EMP Sie haben die richtige Wahl getroffen Zu dieser BedienungsanleitungInhalt Kap. InhaltVerwendungszweck Sicherheitshinweise LieferumfangTaschensender SK Mikrofon ME Verstärker EMP Komponenten des Soundfield Systems Verstärker EMPTaschensender SK Taste on / OFFInbetriebnahme VerstärkerMikrofon an Sender anschließen Mikrofon MEAntenne einschrauben Sender an der Kleidung befestigenBasissystem aufbauen Lautsprecher im Raum aufstellenLautsprecher anschließen Soundfield System ein- und ausschalten Anzeigen Der schnelle Einstieg in die BedienungTasten Anzeigen im LC-Display des EmpfängersBatterieanzeige BalkenanzeigePeak-Anzeige Audiogeräte anschließen Lautstärke des Audiogeräts einstellenAusgangspegel für FM-Sender einstellen Funk-Mikrofon-Anlagen für Hörgeschädigte anschließenVerstärker mit zwei Funk-Mikrofon-Anlagen FM-Anlage testenSpezielle Anwendungen System mit bis zu 8 Lautsprechern aufbauenLautsprecher anschließen Aufnahmegeräte anschließen Mono-Aufnahmegeräte Stereo-AufnahmegerätAufnahmepegel einstellen System mit mehreren Sendern aufbauen Team-Teaching Empfänger anschließenSystem mit 2 Sendern und einem Wiedergabegerät auf- bauen Für den Taschensender SK Empfehlungen und TippsFür das Headset-Mikrofon ME Für optimalen EmpfangSpezielle Einstellungen Grundfunktionen des Sennheiser-BedienmenüsWichtig SenSit Empfindlichkeit einstellen nur SenderStandardanzeige umschalten SqELCHFestspeicherplatz auswählen Festspeicherplätze programmierenVorgehen bei der Programmierung Wichtiger HinweisCh no Kanalnummer einstellenBedienung sperren Sperre einschaltenSperre aufheben Soundfield System akustisch an den Raum anpassen Pflege und Wartung Poppschutz austauschenFehler Mögliche Ursache Fehlercheckliste10 Störungssuche AbhilfeSendeantenne hat sich gelöst Empfohlenes Zubehör Technische Daten Speaker OUTEMP 2015 Soundfield System Thank you for choosing Sennheiser Contents Area of application Delivery includes SK 500 bodypack transmitter ME 3 headmicComponents of the Soundfield System EMP 2015 receiver/amplifier combinationSK 500 bodypack transmitter On / OFF buttonInserting and replacing the battery Setting up the EMPConnecting the antenna and preparing the mains connection Getting readyME 3 headmic Connecting the antennaConnecting the microphone Attaching the transmitter to clothingInstalling the basic system Installing the loudspeakersConnecting the loudspeakers Turning the system components on and off LC display panels OperationButtons ReceiverRed LED Battery status indicationBargraph Peak indicationConnecting external audio devices Adjusting the volume of an external audio deviceMono audio devices Stereo audio device Stereo audio devices Testing the FM system Connecting FM systems for persons with impaired hearingAdjusting the output level for FM transmitters EMP 2015 with two FM systemsInstalling a system with up to eight loudspeakers Special applicationsConnecting the loudspeakers Connecting sound recording devices Adjusting the recording levelMono sound recording devices Stereo sound recording device Connecting an EM 500 receiver Adjusting the volume of the connected receiversAdapting the system sensitvity to the connected receivers For the SK 500 bodypack transmitter Recommendations and tipsFor the ME 3 headmic For optimum receptionSpecial adjustments Basic functions of the Sennheiser operating menuAdjusting the sensitvity transmitter only Selecting the content of the standard display Adjusting the squelch threshold receiver section onlySelect a frequency memory Configuring a frequency memoryOperating steps for configuring a frequency memory Important noteAssign a channel number Activating/deactivating the lock mode Activating the lock modeDeactivating the lock mode Acoustically adapting the Soundfield System to a room Care and maintenance Replacing the windscreenTroubleshooting Error checklistProblem Possible cause What to do Problem Possible cause What to do Recommended accessories Specifications Line OUT Speaker OUT