Sennheiser EMP 2015 manual Connecting sound recording devices, Adjusting the recording level

Page 53

2 mono sound recording devices

1 stereo sound recording device

Connecting sound recording devices

You can connect sound recording devices (e.g. tape recorder, dictating machine, etc.) to the RCA sockets (LINE OUT) of the amplifer. The connected device records the same signal that can be heard in the room through the loudspeakers. If possible, connect the sound recording device via its line input (LINE IN, REC. IN, AUX IN, TB IN or similar).

Connect the RCA plugs of the sound recording devices to the RCA sockets

(LINE OUT) at the rear of the EMP 2015. For correct connection of the different audio devices, please refer to the diagrams at the left.

Adjusting the recording level

The recording level is independent of the setting of the volume controls and . It is, however, dependent on the setting of the line input sensitivity

control (LINE IN) . Control	adjusts the input level of the connected
audio device.

The recording level of the line output can be adjusted from 0 to 700 mVrms (corresponds to minus infinite to up to 0 dBU).

1.The sound recording device is connected via its line input (LINE IN, REC. IN, AUX IN, TB IN or similar):

Turn control clockwise as far as possible and adjust the input level of the sound recording device.

2. The sound recording device is connected via its microphone input:

Set the input level of the sound recording device to maximum and

use control		to adjust the recording level so that, during loud
passages, distortion is avoided.
Note:
If control	is turned counterclockwise as far as possible, no audio signal

will be available at the line output .

If you have connected two mono sound recording devices, the control adjusts the recording level of both devices.

55

Image 53

Contents Soundfield System EMP Zu dieser Bedienungsanleitung Sie haben die richtige Wahl getroffenKap. Inhalt InhaltVerwendungszweck Taschensender SK Mikrofon ME Verstärker EMP SicherheitshinweiseLieferumfang Verstärker EMP Komponenten des Soundfield SystemsTaste on / OFF Taschensender SKVerstärker InbetriebnahmeAntenne einschrauben Mikrofon MEMikrofon an Sender anschließen Sender an der Kleidung befestigenLautsprecher im Raum aufstellen Basissystem aufbauenLautsprecher anschließen Soundfield System ein- und ausschalten Tasten Der schnelle Einstieg in die BedienungAnzeigen Anzeigen im LC-Display des EmpfängersPeak-Anzeige BatterieanzeigeBalkenanzeige Lautstärke des Audiogeräts einstellen Audiogeräte anschließenVerstärker mit zwei Funk-Mikrofon-Anlagen Funk-Mikrofon-Anlagen für Hörgeschädigte anschließenAusgangspegel für FM-Sender einstellen FM-Anlage testenSystem mit bis zu 8 Lautsprechern aufbauen Spezielle AnwendungenLautsprecher anschließen Aufnahmepegel einstellen Aufnahmegeräte anschließenMono-Aufnahmegeräte Stereo-Aufnahmegerät Empfänger anschließen System mit mehreren Sendern aufbauen Team-TeachingSystem mit 2 Sendern und einem Wiedergabegerät auf- bauen Für das Headset-Mikrofon ME Empfehlungen und TippsFür den Taschensender SK Für optimalen EmpfangWichtig Spezielle EinstellungenGrundfunktionen des Sennheiser-Bedienmenüs Empfindlichkeit einstellen nur Sender SenSitSqELCH Standardanzeige umschaltenVorgehen bei der Programmierung Festspeicherplätze programmierenFestspeicherplatz auswählen Wichtiger HinweisKanalnummer einstellen Ch noSperre aufheben Bedienung sperrenSperre einschalten Soundfield System akustisch an den Raum anpassen Poppschutz austauschen Pflege und Wartung10 Störungssuche FehlerchecklisteFehler Mögliche Ursache AbhilfeSendeantenne hat sich gelöst Empfohlenes Zubehör Speaker OUT Technische DatenEMP 2015 Soundfield System Thank you for choosing Sennheiser Contents Area of application SK 500 bodypack transmitter ME 3 headmic Delivery includesEMP 2015 receiver/amplifier combination Components of the Soundfield SystemOn / OFF button SK 500 bodypack transmitterConnecting the antenna and preparing the mains connection Setting up the EMPInserting and replacing the battery Getting readyConnecting the microphone Connecting the antennaME 3 headmic Attaching the transmitter to clothingInstalling the loudspeakers Installing the basic systemConnecting the loudspeakers Turning the system components on and off Buttons OperationLC display panels ReceiverBargraph Battery status indicationRed LED Peak indicationMono audio devices Stereo audio device Stereo audio devices Connecting external audio devicesAdjusting the volume of an external audio device Adjusting the output level for FM transmitters Connecting FM systems for persons with impaired hearingTesting the FM system EMP 2015 with two FM systemsSpecial applications Installing a system with up to eight loudspeakersConnecting the loudspeakers Mono sound recording devices Stereo sound recording device Connecting sound recording devicesAdjusting the recording level Adjusting the volume of the connected receivers Connecting an EM 500 receiverAdapting the system sensitvity to the connected receivers For the ME 3 headmic Recommendations and tipsFor the SK 500 bodypack transmitter For optimum receptionBasic functions of the Sennheiser operating menu Special adjustmentsAdjusting the sensitvity transmitter only Adjusting the squelch threshold receiver section only Selecting the content of the standard displayOperating steps for configuring a frequency memory Configuring a frequency memorySelect a frequency memory Important noteAssign a channel number Deactivating the lock mode Activating/deactivating the lock modeActivating the lock mode Acoustically adapting the Soundfield System to a room Replacing the windscreen Care and maintenanceProblem Possible cause What to do TroubleshootingError checklist Problem Possible cause What to do Recommended accessories Line OUT Speaker OUT Specifications