TOA Electronics VM-2120 instruction manual Surveillance I/O blank panel

Page 39

Surveillance I/O blank panel

Step 3. Detach the surveillance I/O blank panel on the amplifier rear panel by removing 2 fixing snap rivets.

Snap rivet
D-sub connector	SV-200M Board
D-sub connector

Step 4. Unscrew 2 hexagonal sleeves mounted on the 25-pin

D-sub connector on the SV-200M Board.

Hexagonal sleeve

Step 5. Connect the SV-200M Board to the VM amplifier's boards with the connection cables.

5-1.Plug out the jumper connector from the relay board connector (CN1003) shown below.

5-2.Connect the 2 cables attached to the SV-200M to the connectors in the VM amplifier's boards shown below.

CN6 connection cable

5 -2

CN1003 connection cable

SV-200M Board

CN1003
CN6	CN8
Relay board

D-sub connector

Jumper connector

Rear panel

5 -1

SV-200M Board

Step 6. Using the removed 2 hexagonal sleeves,

mount the SV-200M in the amplifier.

Step 7. Check the DIP switch on the SV-200M Board again Hexagonal sleeve

for correct setting. (See Step 1.)

Step 8. Using the 4 rear panel screws and 6 side panel screws removed in Step 2, replace the amplifier cover.

39

Image 39

Contents System Management Amplifier Table of Contents Remote Microphone Installation When the Unit is in Use Safety PrecautionsSafety Symbol and Message Conventions When Installing the UnitWhen Installing the Unit Remote Microphone RM-200M FeaturesGeneral Description System Management Amplifier VM-2120/VM-2240VM-2120/VM-2240 Handling PrecautionsInstallation Precautions VM-2120/VM-2240 and RM-200M/RM-210System Management Amplifier VM-2120/-2240 Front Nomenclature and FunctionsRear Signal earth terminal Function switch Settings An 8-bit DIP switch and selectsControl input and output connector Control I/O DC power inputSurveillance Board SV-200M Voice Announcement Board EV-200Remote Microphone RM-200M Top Left Side Rear Right SideRemote Microphone Operation Panel Function System ConfigurationSpeaker zones with 2 VM amplifiers Power Supply from the VM Amplifier to Remote Microphone Connection between Remote Microphone and VM AmplifierConnection method vs. Distance Power supply using cables other than Category 5 STP cable System management amplifier VM-2120/-2240 Keys/Indicators Used for Emergency BroadcastEmergency Alert and Evacuation Broadcast Emergency Broadcast EquipmentEmergency Broadcast Operation Typical Example Alert announcement example*3Evacuation announcement example*4 Page Emergency mode Emergency Broadcast SequenceRestoration to general-purpose broadcast Microphone Announcements When Operated by Control Input Broadcast Operation AT the AmplifierBackground Music Broadcast Broadcast volume Remote Microphone GENERAL-PURPOSE BroadcastOperation and Display Sections Broadcast Operation Operation below follows on the previous Press-to-talk operationLock operation Broadcast Source-to-Priority Relationship GENERAL-PURPOSE Broadcast PriorityZone Broadcast source Made a broadcast last Priority Function during BGM Broadcast Chime Function Available Chime Tone TypesHow the Chime Tone Is Used Operating procedure Independent chime activation remote controlWestminster chime Choke Coil Installation Remote Microphone RM or Telephone Paging TEL Input Transformer Installation and ITS Board ModificationTransformer Installation Inputs 1RM/TEL input transformer board Switching Off the Phantom Power SupplyMounting AN Optional EV-200 Voice Announcement Board EV-200 surveillance signal output Switch NoCF Card security cover Mounting AN Optional SV-200M Surveillance Board Speaker line surveillance activation timeCommunications with VM VM-2120 or VM-2240 amplifier Surveillance I/O blank panel Microphone Connection to the VM Amplifier Rack MountingAmplifier Input Connection Two Amplifiers Stack-ConnectionTelephone Paging Input Connections Wire System Connection External Attenuator Control WiringAttenuator C CONTROL*1 Connector pin assignment How to remove cables from connectorChanging the Speaker Line Voltage Control I/O connector pin function table Control I/O Connector FunctionsElectrical characteristics Surveillance I/O connector pin function table Surveillance I/O Connector FunctionsChime Selection table VM Amplifiers Internal Function Switches Remote Microphones Function Switches Connected unit No. table SW3RM RM-200M Unit No. table Routing Assignment Broadcast GROUP/ZONE SettingSetting example mark indicates Set state Default settingRecorded Message-to-Group assignment Operating KeysLighting status Zone-to-Group Assignment OperationAll zones setting and its cancellation Indicator status Group setting contents checkDual indication of group and zone selections Operation for zone selection and its cancellationMessage setting contents check Operation for group selection and its cancellationDual indication of setting item and group selections Recorded Message-to-Group Assignment Operation Linkage Between Remote Microphone and ITS Extension Name Label Preparation Amplifiers Label PreparationRemote Microphones Label Preparation Pattern paper for hand writing Dimensional diagram for printing devices Message Program/Sentence Composition Example Setting items and contentsCompactflash CF Card Recording RecordingMessage Program Example VM-2120/-2240 System Management Amplifier VM-2120/-2240 SpecificationsTo be AWG Remote Microphone RM-200M Voice announcement board EV-200 AccessoriesOptional products Remote microphone extension RM-210Page 133-12-726-70