TOA Electronics VM-2120 instruction manual Emergency Broadcast Sequence, Emergency mode

Page 21

8.4. Emergency Broadcast Sequence

General-purpose broadcast

Depression of the Remote Microphone's Emergency broadcast switch

Activation of Alert input*1 by external equipment.

Activation of Evacuation input*1 by external equipment

Alternate repetition of Alert tone signal and Alert announcement

Live microphone announcement by the Remote Microphone's Talk key

End of set repetition

Alternate repetition of Evacuation tone signal and Evacuation announcement

Live microphone

announcement by

the Remote

Microphone's Talk key

Activation of Emergency Stop input*1 by external equipment

End of Emergency broadcast

(The unit returns to the general-purpose broadcast mode it was in immediately before the Emergency broadcast was started.*2)

*1 Control I/O connector terminal located on the VM amplifier's rear panel

Emergency broadcast can also be stopped by pressing the front panel-mounted Reset key. Note, however, that the zones the unit was broadcasting to just before the emergency broadcast activation may change.

*2 General-purpose broadcast is not restored depending on its type.

[Emergency mode]

•The emergency mode refers to the state where the VM amplifier is making emergency broadcast or where the "VM amplifier's broadcast cutoff control" signal is being transmitted from external emergency broadcast equipment to the VM amplifier (refer to p. 45 "CONTROL I/O CONNECTOR FUNCTIONS").

•When the VM amplifier is placed in the emergency mode that takes precedence over general-purpose broadcast mode, the Emergency indicators of both the amplifier and the Remote microphone will light.

[Restoration to general-purpose broadcast]

For the general-purpose broadcasts cut off when its mode enters the emergency mode, some are restored after emergency mode completion, and some are not.

Broadcast to be restored	Broadcast not restored
Broadcast that is not activated by manual	Broadcast that is activated by manual operation of or
operation of or control from external equipment	control from external equipment

•Broadcast from Inputs 1 – 3 not activated by • Broadcast from Inputs 1 – 3 activated by control input

control input (CTRL 1 – 3).	(CTRL 1 – 3).
• Broadcast from BGM Inputs 1 and 2.	• Broadcast from Remote Microphone
	• Telephone paging
	• Message broadcast
	• Westminster chime

21

Image 21

Contents System Management Amplifier Table of Contents Remote Microphone Installation Safety Symbol and Message Conventions Safety PrecautionsWhen Installing the Unit When the Unit is in UseWhen Installing the Unit General Description FeaturesSystem Management Amplifier VM-2120/VM-2240 Remote Microphone RM-200MInstallation Precautions Handling PrecautionsVM-2120/VM-2240 and RM-200M/RM-210 VM-2120/VM-2240System Management Amplifier VM-2120/-2240 Front Nomenclature and FunctionsRear Control input and output connector Control I/O Function switch Settings An 8-bit DIP switch and selectsDC power input Signal earth terminalSurveillance Board SV-200M Voice Announcement Board EV-200Remote Microphone RM-200M Top Left Side Rear Right SideRemote Microphone Operation Panel Function System ConfigurationSpeaker zones with 2 VM amplifiers Power Supply from the VM Amplifier to Remote Microphone Connection between Remote Microphone and VM AmplifierConnection method vs. Distance Power supply using cables other than Category 5 STP cable Emergency Alert and Evacuation Broadcast Keys/Indicators Used for Emergency BroadcastEmergency Broadcast Equipment System management amplifier VM-2120/-2240Emergency Broadcast Operation Typical Example Alert announcement example*3Evacuation announcement example*4 Page Emergency mode Emergency Broadcast SequenceRestoration to general-purpose broadcast Microphone Announcements When Operated by Control Input Broadcast Operation AT the AmplifierBackground Music Broadcast Broadcast volume Remote Microphone GENERAL-PURPOSE BroadcastOperation and Display Sections Broadcast Operation Operation below follows on the previous Press-to-talk operationLock operation Broadcast Source-to-Priority Relationship GENERAL-PURPOSE Broadcast PriorityZone Broadcast source Made a broadcast last Priority Function during BGM Broadcast Chime Function Available Chime Tone TypesHow the Chime Tone Is Used Operating procedure Independent chime activation remote controlWestminster chime Choke Coil Installation Transformer Installation Input Transformer Installation and ITS Board ModificationInputs 1 Remote Microphone RM or Telephone Paging TELRM/TEL input transformer board Switching Off the Phantom Power SupplyMounting AN Optional EV-200 Voice Announcement Board EV-200 surveillance signal output Switch NoCF Card security cover Mounting AN Optional SV-200M Surveillance Board Speaker line surveillance activation timeCommunications with VM VM-2120 or VM-2240 amplifier Surveillance I/O blank panel Amplifier Input Connection Rack MountingTwo Amplifiers Stack-Connection Microphone Connection to the VM AmplifierTelephone Paging Input Connections Wire System Connection External Attenuator Control WiringAttenuator C CONTROL*1 Connector pin assignment How to remove cables from connectorChanging the Speaker Line Voltage Control I/O connector pin function table Control I/O Connector FunctionsElectrical characteristics Surveillance I/O connector pin function table Surveillance I/O Connector FunctionsChime Selection table VM Amplifiers Internal Function Switches Remote Microphones Function Switches Connected unit No. table SW3RM RM-200M Unit No. table Setting example mark indicates Set state Broadcast GROUP/ZONE SettingDefault setting Routing AssignmentRecorded Message-to-Group assignment Operating KeysLighting status Zone-to-Group Assignment OperationAll zones setting and its cancellation Indicator status Group setting contents checkDual indication of group and zone selections Operation for zone selection and its cancellationMessage setting contents check Operation for group selection and its cancellationDual indication of setting item and group selections Recorded Message-to-Group Assignment Operation Linkage Between Remote Microphone and ITS Extension Name Label Preparation Amplifiers Label PreparationRemote Microphones Label Preparation Pattern paper for hand writing Dimensional diagram for printing devices Compactflash CF Card Recording Setting items and contentsRecording Message Program/Sentence Composition ExampleMessage Program Example VM-2120/-2240 System Management Amplifier VM-2120/-2240 SpecificationsTo be AWG Remote Microphone RM-200M Optional products AccessoriesRemote microphone extension RM-210 Voice announcement board EV-200Page 133-12-726-70