Elmo ISP manual ELMO-WARRANTY Performance

Page 2

2

ELMO-WARRANTY PERFORMANCE

The warranty performance covers only ELMO's products and only the elimination of problems that are due to manufacturing defects resulting in impaired function, deficient workmanship or defective material. Specifically excluded from warranty is the elimination of problems which are caused by abuse, damage, neglect, overloading, wrong operation, unauthorized manipulations etc.

The following maximum warranty period applies:

12 months from the time of operational startup but not later than 18 months from

shipment by the manufacturing plant.

Units repaired under warranty have to be treated as an entity.

A breakdown of the repair procedure (for instance of the repair of a unit into repair of cards) is not permissible.

Damage claims, including consequential damages, which exceed the warranty obligation will be rejected in all cases.

If any term or condition in this warranty performance shall be at variance or inconsistent with any provision or condition (whether special or general) contained or referred to in the Terms and Conditions of Sales set out at the back of Elmo's Standard Acknowledge Form, than the later shall prevail and be effective.

ISP - Rev 6/95

Image 2
Contents Rev 6/95 ISP Rev 6/95 ELMO-WARRANTY Performance Read chapters Table of Contents Balance adjustment Current limit adjustment Protective functions Standard featuresDescription Technical specifications Type DesignationOperation of the servo control Inputs Velocity mode Velocity control using armature voltage feedback Current modeTime dependent peak current limit Current loopCurrent limits Dynamic contouring of continuous and peak current limits Operation of the shunt regulator Protective functions Temperature protectionLoss of velocity feedback signal Short circuit protectionCurrent Command Monitor Input ISP Control Board Page Contact rating 0.5A, 200V, 10W Terminals of ISP Panel Version Mother Board terminals MBA-ISP/N Terminals for ISP mounted in 3U size ENC GNDContact rating 0.5A, 200V, 10W Page MBA ISP/3UE Installation procedures Mounting Wiring2Vdcmin Vdc 0.9Vdcmax AC power supplyLoad inductance Wiring diagrams ISP GNDGround Do not groundAC ISP ISP Control Connections Tachogenerator Feedback ISP Control Connections Armature Voltage Feedback Start Up Procedures Disable by LowEnable by High ISP Control Board See .1 for calculation of other values Converting the amplifier into current modeSelecting the reference signal gain Activating the loss of tacho protection velocity mode only For VtmActivating the dynamic contouring of the current limits Latch mode of the protective functionsVelocity control using tachogenerator feedback IxR compensation For ISP-X/65For ISP-X/135 Current limit adjustment Amplifier adjustment and diagnosticsBalance adjustment Adjusting the motor speed velocity mode only Adjustment of the IxR compensationResponse adjustment velocity mode only Typical velocity response waveforms ISP Rev 6/95 Tables and Summaries Adjusting trimmers LED diagnosticsAppendix a Response adjustment current loop Fig. A-1 Typical current response waveforms ISP Rev 6/95 Appendix B Current limits contour adjustment Velocity TorqueDynamic contouring with armature voltage feedback ISP Rev 6/95 SP1 TOP View SP1 Side View SP1 Side View SP2 TOP View SP2 Side View SP2 Side View SP3 TOP View SP3 Side View SP3 Side View SP4 TOP View SP4 Side View SP4 Side View ISP Rack Mounting 8T and 15T TOP View ISP Rack Mounting 3U/8T Side View 128.7 Front Panel for ISP 3U/8T ISP Rack Mounting 3U/15T -SIDE View ISP Rack Mounting 3U/15T Side View Front Panel for ISP 3U/15T ISP Rack Mounting 3U/12T and 3U/19T TOP View ISP Rack Mounting 3U/12T -SIDE View ISP Rack Mounting 3U/12T Side View Front Panel for ISP 3U/12T ISP Rack Mounting 3U/19T -SIDE View ISP Rack Mounting 3U/19T Side View Front Panel for ISP 3U/19T Enclosure Mechanical Outline List of Elmo Service Centers Europe