Jensen VM9510TS Installation, Pre-installation, Wiring, Using the iAUX3 External AV Connector

							VM9510TS
INSTALLATION
Pre-installation			CAUTION! Be careful not to damage the car wiring.			FINAL INSTALLATION
1. Press the metal levers on both sides to remove the half-
							4
	sleeve from the radio.					5
			4. Place the radio in front of the dashboard opening so the
2. Remove the transport screws.
				wiring can be brought through the mounting sleeve.		1
PREPARE RADIO			Wiring
		1	Complete wiring as illustrated in the wiring diagram on page
			3. Once the wiring is complete, reconnect the battery
			negative terminal. If there is no ACC available, connect the
			ACC lead to the power supply with a switch.				2
			NOTE: When replacing a fuse, be sure to use correct
			type and amperage to avoid damaging the radio. The
7-INCH TFT TFT			VM9510TS uses one 10 amp mini-ATM fuse, located in			3
7	-INCH
	DIGITAL		the black filter box in-line with the main wire harness.
VM9510		AM/FM/DVD/MP3 RECEIVER
		2	Final Installation		Final ISO-DIN Installation
		AV AUX IN
			After completing the wiring connections, turn the unit on to		1.	Remove trim ring.
3.	Install the half-sleeve.		confirm operation (ignition switch must be on). If unit does not		2. Mount factory brackets on new radio using existing
			operate, recheck all wiring until problem is corrected. Once			screws from old radio.
	a. Install adapter if necessary (optional).		proper operation is achieved, turn off the ignition switch and		3.	Slide radio chassis into dash opening and secure.
	b. Install half-sleeve into adapter or dashboard (only		proceed with final mounting of the chassis.
					4.	Reinstall dash panel.
		use the supplied screws). Do not force the sleeve	1.	Connect wiring adapter to existing wiring harness.
		into the opening or cause it to bend or bow.
			2.	Connect antenna lead.
	c.	Locate the series of bend tabs along the top,				FINAL ISO-DIN INSTALLATION
			3. Carefully slide the radio into the half-sleeve making sure
		bottom and sides of the mounting sleeve. With the
				it is right-side-up until it is fully seated and the spring
		sleeve fully inserted into the dashboard opening,
				clips lock it into place.		3
		bend as many of the tabs outward as necessary so
		that the sleeve is firmly secured to the dashboard.	NOTE: For proper operation of the CD/DVD player, the
	d.	Install support strap to make the unit more stable.
			chassis must be mounted within 20° of horizontal. Make
			sure the unit is mounted within this limitation.				2
INSTALL HALF SLEEVE
			4.	Attach one end of the perforated support strap
						1
				(supplied) to the screw stud on the rear of the chassis
		3d		using the hex nut provided. Fasten the other end of the		4
				perforated strap to a secure part of the dashboard either
		3c
				above or below the radio using the screw and hex nut
				provided. Bend the strap to position it as necessary.	Using the iAUX3 External AV Connector
			CAUTION! The rear of the radio must be supported with		The iAUX3 allows you to connect a variety of external
					devices, including a VCR, DVD player, portable MP3 player,
			the strap to prevent damage to the dashboard from the		etc., to your VM9510TS without removing the radio.
			weight of the radio or improper operation due to
		3a
			vibration.		To install the iAUX3, connect it to the AUX-IN cables on the
					back of the VM9510TS (see the Wiring Diagram” on page 3),
			5. Replace any items you removed from the dashboard.		and then install the iAUX3 in a location convenient for
		3b			plugging in auxiliary devices.

2