Alpine TME-M790 Connections, Connect to the vehicle’s foot brake lead or brake lamp lead

Page 20

Installation and Connections

Connections

White/Brown

White/Brown

Yellow/Black

Yellow/Blue

Pink/Black

8

Red

8

Yellow

REMOTE OUT

AUX1

REMOTE OUT

AUX2

FOOT BRAKE

PARKING BRAKE

AUDIO

INTERRUPT OUT

IGNITION

BATTERY

1

1

2

3

4

5

6

To remote input lead.

To remote input lead.

To the foot brake cord or brake lamp cord.

To the parking brake signal lead.

Connect to an IN INT compatible product.

Ignition key

Black

GND

7

Battery

Monitor

VIDEO

L

AUDIO

R

NAVIGATION

 

OUTPUT AUX

 

 

DISPLAY OUTPUT

AUX INPUT 2

 

AUX INPUT 1

 

(MONO)

 

 

(MONO)

 

R AUDIO L

VIDEO

R AUDIO L

VIDEO

 

 

 

 

 

 

 

 

1Remote Control Output Lead (White/Brown) Connect this lead to the remote control input lead. This lead outputs the controlling signals from the remote control.

2Foot Brake Lead (Yellow/Black)

Connect to the vehicle’s foot brake lead or brake lamp lead.

3Parking Brake Lead (Yellow/Blue)

Connect this lead to the power supply side of the parking brake switch to transmit the parking brake status signals to the TME-M790.

4Audio Interrupt Out Lead (Pink/Black)

5Switched Power Lead (Ignition) (Red) Connect this lead to an open terminal on the vehicle’s fuse box or another unused power source which provides (+) 12V only when the ignition is turned on or in the accessory position.

6Battery Lead (Yellow)

Connect this lead to the positive (+) post of the vehicle’s battery.

7Ground Lead (Black)

Connect this lead to a good chassis ground on the vehicle. Make sure the connection is made to bare metal and is securely fastened using the sheet metal screw provided.

8Fuse Holder (5A)

To prevent external noise from entering the audio system.

Locate the unit and route the leads at least 10cm away from the car harness.

Keep the battery power leads as far away from other leads as possible.

Connect the ground lead securely to a bare metal spot (remove the coating if necessary) of the car chassis.

If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various Alpine noise suppressors, contact them for further information.

Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.

18-EN

Image 20
Contents TME-M790 Page Contents USE the Correct Ampere Rating When Replacing Fuses Precautions Using Face Cover Basic OperationsInitial System Start-up Raising the MonitorTurning Power On or Off Adjusting the Monitor Viewing AngleAdjusting the Volume Switching the SourceSwitching Display Modes Viewing the switching display modesMode 1 Wide Mode 2 ZoomMode 3 Cinema Mode 4 NormalOther Useful Features Adjusting Brightness of PictureAdjusting Tint of Picture Press the SET UP button to finish adjustmentsSetting the Brightness of the Backlight Adjusting the Lowest Level of the BacklightSetting Automatic Opening Closing of Monitor AutoSetting the External Device Interrupt Mode Selecting Rear MonitorLink NAVSwitching the Opening Screen Switching the Video ScreenUsing the External Input Terminal Turning Sound Guide Function On or Off12-EN Case of Difficulty SpecificationsInformation Installation and Connections Do not Splice Into Electrical CablesPrecautions To install using the vehicles genuine bracket InstallationPlace of installation TME-M790 Monitor If the ACC power supply is not availableTME-M790 Connections Connect to the vehicle’s foot brake lead or brake lamp leadParking Brake Lead Yellow/Blue Ground Lead BlackAudio Output Connector RGB Output ConnectorSystem Connections Video Output TerminalPage Numéros Dappel DU Service À LA Clientele Produits Couvert PAR LA GarantieDurée DE LA Garantie Limitation DES Garanties TacitesLength of Warranty Lifetime Tape Head WarrantyWhat is Covered What is not Covered