Blaupunkt RTM 127 Radio operation with RDS Radio Data System, Enter the frequency directly

Page 20

Radio operation with RDS (Radio Data System)

Search

Up

Down

<</ >> Up/Down in increments

(for FM only when AF is switched off)

Manual tuning with << / >>

You can also tune in a station manually.

Important:

AF must be switched off (i.e. the ”AF” or ”REG” symbol does not light up in the dis- play).

If necessary, deactivate this function:

• Press AF/#.

Manual tuning:

Press << / >>; the frequency will change in degrees in the downwards or upwards direction.

If you hold down the right or left part of the rocker switch, the frequency scan will ac- celerate in the corresponding direction.

Enter the frequency directly

For FM or FMT, it is possible to enter the station frequency directly.

Start your entry

by pressing 0.

Then enter the frequency, beginning with the first digit. You need not enter a decimal point.

Press CL to cancel this process or OK to confirm your entry.

Scroll through the broadcasting networks (FM only)

You can use the << / >> buttons to tune into stations in your reception area.

If it is possible to receive several programs in the same broadcasting network, you can scroll through them in the forwards direc- tion by pressing >>, or backwards using the

<<button, e.g. NDR 1, 2, 3, 4, N-JOY. Important: You must have tuned into these stations at least once previously and “AF” must be active (lights up in the display).

Start Travelstore, for example:

Press BND for 2 seconds; the system will start to run through the frequency band.

If “AF”does not light up,

• press AF/#.

This fulfils the requirements for selecting sta- tions with << / >>.

Store radio stations

You can store the following number of radio stations for the different wavebands:

FM

19

TS (FM-Travelstore)

9

MW

9

LW

9

Use BND to select the desired wave- band.

Select a radio station using the rocker switch (automatically with / or man- ually with << / >>).

Press the desired station preset for ap- prox. 1 second until you hear a beep.

If you want to store the radio station on a two-digit preset

press ”1”briefly and then press the second button within two seconds and hold it down until you hear a beep.

You have now stored the radio station. The station preset will appear in the display.

Note:

If you tune into a station which has already been stored before, then the corresponding preset position and memory bank will flash

86

Image 20
Contents Helsinki RTM PAC Contents Radio, CD changer optional Contents Radio, CD changer optional Contents Telephone Contents Telephone Safety standards Safety informationImportant information General informationInstallation Using the telephone in critical areasImportant information Emergency callsAccessories Starting up the Radiophone KeyCard and SIM cardBasic information Train KeyCard/SIM cards KeyCard and SIM cardRemove the KeyCard/SIM card Displaying the radio pass data DSC learn modeOptical warning of anti-theft protection On/off Volume Switch the unit on/off with the Key- CardSwitch the unit on/off via the ignition Operation in combination with an ignition timerTS / BND Alter the volumeSRC Source Selection buttons Radio mode Enter the frequency directly Store radio stationsAF / # MIX= Display Flashing card tongue? Rocker switch PlayedSelect operating mode Audio modeStation tuning Radio operation with RDS Radio Data SystemAF Alternative Frequency REG regional programManual tuning with Radio operation with RDS Radio Data SystemEnter the frequency directly Scroll through the broadcasting networks FM onlyAlter search sensitivity Switch from stereo to mono FM onlyRecall stored radio stations Switch traffic announcement priority on/off Traffic program station reception with RDS-EONRadiotext Beep toneSwitch CD changer operation on Switch off the warning beepCD changer operation optional Automatic search startCD changer operation optional Enter CD namesClear CD name ClearProgramming with DSC PaX PAC memoryProgramming with DSC Setup DSC menu SetupIgnition timer ResetUser mode KeyCard LEDOverview of the DSC default set- tings Setup TA volumeProgramming with DSC Radio DSC Menu RadioOverview of the DSC default settings Radio Save settings / end DSC programmingSensitivity Music/SpeechPage Telephone operation Telephone operation General informationPIN code Insert the SIM card/enter your PIN codeGSM emergency calls Telephone operationMake your first telephone call Quick telephone reference MIX Quick telephone referenceAF / # ? Rocker switch @ MEQuick telephone reference Using the telephone GSM network service areaUsing the telephone Dial a telephone numberCall waiting 2nd caller Answer/end a callRedial function Broker’s call/hold Conference callsInternational calls PaX PAC memoryMake telephone calls using the handset accessory Programming with DSCSelect the function SelectPhone book menu How to enter a name/textProgramming with DSC Phone book Find an entry by name Enter letters/charactersCapital and small letters Move the cursor in the input text boxFind an entry by position EntrySelect an entry by remote ControlAdd entry Access CapacityVolume Hands-free volumeHandset volume Show my phone numberAutomatic answer Automatic redialRinging tone My numberAOC parameters Advice of Charge Audible call timerExternal alarm PIN-codeOverview of the factory default Settings in the Setup menuTA Traffic Announcement During a telephone callProgramming with DSC Call Menu Call menuCall mailbox SMS messagesBroadcast Network selection ParametersSearch method Available networksCall meters Preferred networksCall forwarding Enter data for call forwardingPractical example of call forwarding Call barring Enter data for call barring Phone lockUser group Specifications AmplifierTelephone TunerGlossary Glossary Speed-dial User groupIndex Index Selecting a CD Selecting a track Bosch Gruppe