Blaupunkt RTM 127 Traffic program station reception with RDS-EON, Radiotext, Beep tone

Page 22

Traffic program station reception with RDS-EON

Radiotext

This is an RDS function which transmits text from the radio station selected. Depending on the radio station, these texts will vary in content, e.g. short news reports, program information, advertising.

For further information, refer to “Program- ming with DSC –Radio”.

The abbreviation “EON” stands for En- hanced Other Networks which means that information is exchanged between the ra- dio stations belonging to the same broad- casting network.

Many FM broadcasters provide traffic mes- sages for their service area at regular inter- vals.

All traffic program stations transmit a spe- cial carrier signal along with their programs, which is decoded by your car radio. If this signal is identified, “TP” will appear in the display (Traffic Program).

In addition to these, there are also stations which do not actually transmit traffic pro- grams themselves, but by using RDS-EON it is possible to receive the traffic messages broadcast by another traffic program station in the same radio network.

If you wish to have the priority for traffic an- nouncements activated while listening to one of these stations (e.g. NDR 3), “TA” must appear in the display.

If a traffic announcement is broadcast, the radio will automatically switch to the linked traffic program station (in this case, NDR 2) for the duration of the message and return to the original program (NDR 3) afterwards.

Switch traffic announcement priority on/off

If the priority for traffic announcement pro- grams is activated, “TA” will light up in the display.

To switch the priority on or off:

• Press TA.

If you press TA while a message is being broadcast, the message will be interrupted for all operating modes for the duration of this message only.

The unit will then switch back to its previous status. The priority for all other traffic mes- sages will remain active.

Please note that several buttons have no function during traffic announcements.

Adjust the volume for traffic announce- ments and the beep tone

Although this volume was preset at the fac- tory, you can alter it using the DSC function (see “Programming with DSC – TA VOL- UME”).

Beep tone

When a traffic program station is activated (”TA” in the display), you will hear a warn- ing beep approx. 30 seconds after you leave the reception area of the traffic program sta- tion you are currently tuned into.

88

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Helsinki RTM PAC Contents Radio, CD changer optional Contents Radio, CD changer optional Contents Telephone Contents Telephone Important information Safety standardsSafety information General informationImportant information InstallationUsing the telephone in critical areas Emergency callsAccessories Basic information KeyCard and SIM cardStarting up the Radiophone Remove the KeyCard/SIM card KeyCard and SIM cardTrain KeyCard/SIM cards Optical warning of anti-theft protection DSC learn modeDisplaying the radio pass data Switch the unit on/off via the ignition On/off VolumeSwitch the unit on/off with the Key- Card Operation in combination with an ignition timerSRC Source Alter the volumeTS / BND AF / # Selection buttons Radio mode Enter the frequency directlyStore radio stations MIX= Display Flashing card tongue? Rocker switch PlayedSelect operating mode Audio modeAF Alternative Frequency Station tuningRadio operation with RDS Radio Data System REG regional programEnter the frequency directly Manual tuning withRadio operation with RDS Radio Data System Scroll through the broadcasting networks FM onlyRecall stored radio stations Switch from stereo to mono FM onlyAlter search sensitivity Radiotext Switch traffic announcement priority on/offTraffic program station reception with RDS-EON Beep toneCD changer operation optional Switch CD changer operation onSwitch off the warning beep Automatic search startClear CD name CD changer operation optionalEnter CD names ClearProgramming with DSC PaX PAC memoryProgramming with DSC Setup DSC menu SetupUser mode Ignition timerReset KeyCard LEDProgramming with DSC Radio Overview of the DSC default set- tings SetupTA volume DSC Menu RadioSensitivity Overview of the DSC default settings RadioSave settings / end DSC programming Music/SpeechPage Telephone operation PIN code Telephone operationGeneral information Insert the SIM card/enter your PIN codeMake your first telephone call Telephone operationGSM emergency calls Quick telephone reference AF / # Quick telephone referenceMIX ? Rocker switch @ MEQuick telephone reference Using the telephone GSM network service areaUsing the telephone Dial a telephone numberRedial function Answer/end a callCall waiting 2nd caller Broker’s call/hold Conference callsInternational calls PaX PAC memorySelect the function Make telephone calls using the handset accessoryProgramming with DSC SelectProgramming with DSC Phone book How to enter a name/textPhone book menu Capital and small letters Find an entry by nameEnter letters/characters Move the cursor in the input text boxSelect an entry by remote Find an entry by positionEntry ControlAdd entry Access CapacityHandset volume VolumeHands-free volume Show my phone numberRinging tone Automatic answerAutomatic redial My numberAOC parameters Advice of Charge Audible call timerExternal alarm PIN-codeTA Traffic Announcement Overview of the factory defaultSettings in the Setup menu During a telephone callCall mailbox Programming with DSC Call MenuCall menu SMS messagesBroadcast Search method Network selectionParameters Available networksCall meters Preferred networksCall forwarding Enter data for call forwardingPractical example of call forwarding Call barring User group Phone lockEnter data for call barring Telephone SpecificationsAmplifier TunerGlossary Glossary Speed-dial User groupIndex Index Selecting a CD Selecting a track Bosch Gruppe
Top Page Image Contents