Blaupunkt TCM 169 operating instructions Programming with DSC Radio, Cassette, Changer optional

Page 27

Programming with DSC Radio, Cassette, Changer (optional)

You cannot alter the programming for important DSC settings unless you have entered the access code first (refer to the DSC menu item “CHANGE ACCESS- CODE”).

LOUDNESS

Boosts low frequencies for more bass, es- pecially at low volume.

LOUD 1 - minimum boost LOUD 6 - maximum boost

Enter the original code (in this case “0000”) and press OK.

Enter the new code, press OK. Enter the new code once again, press OK.

IGNITION TIMER

RadioDEUTSCH

/ Select function

<</ >> Make setting

MASTER RESET

This menu item will appear only if a Key- Card is inserted.

Important!

This function will reset all of the settings in the DSC menu including the telephone menu to the factory default settings.

All of the trained KeyCards and SIM cards will be deleted, except for the KeyCard cur- rently in the unit.

If this menu item is selected, it will be nec- essary to enter the access code after OK. Enter the access code, press OK.

The display will show “MASTER RESET?”: Press CL to cancel this function, press OK to reset all of the settings to the default set- tings.

CHANGE ACCESSCODE

The access code is used to access the im- portant DSC menu items (also for telephone operation). At the factory, this code is set to “0000”.

If you would like to alter it be sure to make

a note of the new code!

Use this setting to ensure that the car radio will play for a maximum of 90 minutes after the ignition has been switched off.

0 = ignition timer switched off.

AUXILIARY SOURCE

This menu item will not appear if a CD changer (A 05 or A 06) has been connected to the system.

The default setting is “AUXILIARY SOURCE OFF”.

If an external piece of equipment is connect- ed to the system, this setting must be switched to “AUXILIARY SOURCE ON”.

VARIOCOLOUR

Adjusts the colour of the display illumina- tion to the dashboard illumination.

green

....................................................''

red

KEY TONE

After a key is pressed, a short beep is emit- ted as confirmation.

Set volume from 0 to 9 (0 = off).

ENGLISHTelefon

TelephoneRadio

91

Image 27

Contents Monte Carlo TCM Remote control RCT 07 optional Contents Radio, Cassette, Changer Option Contents Telephone General information Safety standardsSafety information Important informationEmergency calls Using the telephone while drivingUsing the telephone in critical areas Important informationAccessories InstallationInternational telephone informa- tion GuaranteeKeyCard and SIM card Basic informationStarting up the Radiophone Train KeyCard/SIM cards Training or replace KeyCard/ SIM card using DSCKeyCard and SIM card Removing the KeyCard/SIM cardCare of your KeyCard/SIM card DSC learn modeDisplaying the radio pass data Optical warning of anti-theft protectionSwitching the radio on when the ig- nition is switched off On/off VolumeSwitching the unit on/off with the KeyCard Switching the unit on/off via the ig- nitionEject cassette Track switchSRC Source TS / BNDAF / # Cassette loading slotStoring radio stations Recalling stored radio stations -SeCassette operation Changer operation optional = MIXDisplay Radio operation aTape operation Flashing card tongueStop this function by pressing or the opposite button Corresponding function must be activated Additional rocker switch functionsAdditional settings possible with AUD DSC mode C ME UnitRadio, tape deck, CD changer optional, auxiliary source Audio modeAF Alternative Frequency REG regional programmeSelecting a waveband Station tuningRadio operation with RDS Radio Data System Entering the frequency directlyStoring radio stations Scrolling through the broadcast- ing networks FM onlySelecting the seek-tuning sensi- tivity Switching from stereo to mono FM onlyRecalling stored radio stations Traffic programme station reception with RDS-EON Switching traffic announcement priority on/offAutomatic seek tuning start Switching off the beep toneOperating the cassette deck Care instructions Operating the cassette deckTape equalisation Dolby B NRSwitching CD changer operation on CD changer operation optionalSelecting the CD and the track Store CancelSelect AlterProgramming with DSC Radio, Cassette, Changer optional = ignition timer switched offMusic/voice is switched off Cards can only be programmed with the help of the DSC menuOn All of the menu items are available End DSC programming/save changes You can choose among the following oper- ating modesOverview of the DSC default settings Telephone operation Reactivating the SIM card Operating the telephonePIN code Inserting the SIM card/ entering your PIN codeDo not hang up until you are told to do so Operating the telephoneMaking your first telephone call GSM emergency callsSelection buttons Quick reference for using the telephoneVolume On/OffTelephone-book menu Enter PIN code Setup menu/Call menuTo switch back to the telephone mode Press briefly Displays Radio menu@ Rocker switch Save telephone numbers and names Using the telephoneGSM network service area Switching to telephone modeDialling a telephone number Using the telephoneSave telephone numbers from the note- pad Redial functionAnswering/ending a call AutomaticBroker’s call/hold Call waiting 2nd callerInternational calls Making telephone calls using the handset special accessorySetting up a conference call Conference callsTip How to place telephone calls in foreign countriesHow to receive calls Teleph. number Blaupunkt You enter +49512149107 Phone book menuPhone book menu How to enter a name/textFinding an entry by name Prevent access Show my phone numberCheck capacity Add entry Finding an entry by positionAltering, deleting, moving or copying the entry End DSC Press CL, the altered setting will not be storedProgramming with DSC Telephone Store/confirm113 Programming with DSC Telephone -Setup menuProgramming in the setup menu Select the setup menu by pressingAutomatic redial Ringing tone volume Automatic answer Operating modeHands-free volume Handset volumeCall meter format SMS toneEntered Audible call timerSet charge parameters PIN codeBe sure to make a note of the new code if you change it Alter access codeFollowing settings will be deleted External alarmHands-free operation is possible on all four channels Overview of the basic factory settings in the set-up menuExtended menu Ring signal Hands-free channel TA during call119 Press CL, the new setting will not be storedProgramming with DSC Telephone -Call menu Programming in the Call MenuPress OK You can display the message by press- ing Call mailbox Received SMS messagesSelecting the message Reading messagesCalling the sender or another telephone Sending SMS messagesSender Network selection Cell Broadcast Call meters Call forwardingCall barring Fixed dial numbers Phone lockClosed user group Overview of the basic factory settings in the call menuGlossary Telephone SpecificationsAmplifier TunerIndex Index Service numbers 042 175 873Bosch Gruppe