Blaupunkt TCM 169 Radio operation with RDS Radio Data System, Station tuning

Page 19

Radio operation with RDS (Radio Data System)

If you wish to continue listening to the first programme, switch REGIONAL ON by

•pressing AF/# for approximately 1 sec- ond until “REGIONAL ON” appears in the first line.

When the regional function has been switched on “REG” will replace “AF” in the display.

If you leave the service area of the regional programme you are currently tuned into, or if you would like to take advantage of the full RDS service, switch to “REGIONAL OFF”.

•Press AF/# for approximately 1 second until “REGIONAL OFF” appears.

Station tuning

Seek tuning /

•Press /; the car radio will automati- cally search for the next station.

If you hold down / (also applies to re- mote control operation), seek tuning will speed up in upwards or downwards direc- tion.

Manual tuning:		DEUTSCH
• Press << / >>; the frequency will
change in degrees in the downwards
or upwards direction.

If you hold down the right or left part of the
rocker switch, the frequency scan will speed		Radio
up in the corresponding direction.
Entering the frequency directly

For FM or FMT, it is possible to enter the		Telefon
station frequency directly.
Start your entry
• by pressing 0.
• Then enter the frequency, beginning

with the first digit. You need not enter

Selecting a waveband

You can select between the following wave- bands:

Seek tuning

Up

Down

<</ >> Up/Down in increments (for FM only when AF is switched off)

	a decimal point.	ENGLISH
	Press CL to cancel this process or OK to
	confirm your selection.
	confirm your selection.

FM 87.5 - 108 MHz

MW 531 - 1602 kHz

LW 153 - 279 kHz

•Use BND to select the waveband. Press repeatedly if necessary.

Manual tuning with << / >>

You can also tune in a station manually.

Important:

AF must be switched off (i.e. the “AF” or “REG” symbol does not light up in the dis- play).

If necessary, deactivate this function:

•Press AF/#.

Radio

Telephone

83

Image 19

Contents Monte Carlo TCM Remote control RCT 07 optional Contents Radio, Cassette, Changer Option Contents Telephone General information Safety standardsSafety information Important informationEmergency calls Using the telephone while drivingUsing the telephone in critical areas Important informationAccessories InstallationInternational telephone informa- tion GuaranteeBasic information KeyCard and SIM cardStarting up the Radiophone Train KeyCard/SIM cards Training or replace KeyCard/ SIM card using DSCKeyCard and SIM card Removing the KeyCard/SIM cardCare of your KeyCard/SIM card DSC learn modeDisplaying the radio pass data Optical warning of anti-theft protectionSwitching the radio on when the ig- nition is switched off On/off VolumeSwitching the unit on/off with the KeyCard Switching the unit on/off via the ig- nitionEject cassette Track switchSRC Source TS / BNDAF / # Cassette loading slotStoring radio stations Recalling stored radio stations -SeCassette operation Changer operation optional = MIXDisplay Radio operation aFlashing card tongue Tape operationStop this function by pressing or the opposite button Corresponding function must be activated Additional rocker switch functionsAdditional settings possible with AUD DSC mode C ME UnitRadio, tape deck, CD changer optional, auxiliary source Audio modeAF Alternative Frequency REG regional programmeSelecting a waveband Station tuningRadio operation with RDS Radio Data System Entering the frequency directlyStoring radio stations Scrolling through the broadcast- ing networks FM onlySwitching from stereo to mono FM only Selecting the seek-tuning sensi- tivityRecalling stored radio stations Traffic programme station reception with RDS-EON Switching traffic announcement priority on/offAutomatic seek tuning start Switching off the beep toneOperating the cassette deck Care instructions Operating the cassette deckTape equalisation Dolby B NRCD changer operation optional Switching CD changer operation onSelecting the CD and the track Store CancelSelect AlterProgramming with DSC Radio, Cassette, Changer optional = ignition timer switched offCards can only be programmed with the help of the DSC menu Music/voice is switched offOn All of the menu items are available End DSC programming/save changes You can choose among the following oper- ating modesOverview of the DSC default settings Telephone operation Reactivating the SIM card Operating the telephonePIN code Inserting the SIM card/ entering your PIN codeDo not hang up until you are told to do so Operating the telephoneMaking your first telephone call GSM emergency callsSelection buttons Quick reference for using the telephoneVolume On/OffTelephone-book menu Enter PIN code Setup menu/Call menuTo switch back to the telephone mode Press briefly Displays Radio menu@ Rocker switch Save telephone numbers and names Using the telephoneGSM network service area Switching to telephone modeDialling a telephone number Using the telephoneSave telephone numbers from the note- pad Redial functionAnswering/ending a call AutomaticBroker’s call/hold Call waiting 2nd callerInternational calls Making telephone calls using the handset special accessorySetting up a conference call Conference callsTip How to place telephone calls in foreign countriesHow to receive calls Teleph. number Blaupunkt You enter +49512149107 Phone book menuPhone book menu How to enter a name/textFinding an entry by name Show my phone number Prevent accessCheck capacity Finding an entry by position Add entryAltering, deleting, moving or copying the entry End DSC Press CL, the altered setting will not be storedProgramming with DSC Telephone Store/confirm113 Programming with DSC Telephone -Setup menuProgramming in the setup menu Select the setup menu by pressingAutomatic redial Ringing tone volume Automatic answer Operating modeHands-free volume Handset volumeCall meter format SMS toneEntered Audible call timerSet charge parameters PIN codeBe sure to make a note of the new code if you change it Alter access codeFollowing settings will be deleted External alarmHands-free operation is possible on all four channels Overview of the basic factory settings in the set-up menuExtended menu Ring signal Hands-free channel TA during call119 Press CL, the new setting will not be storedProgramming with DSC Telephone -Call menu Programming in the Call MenuPress OK You can display the message by press- ing Call mailbox Received SMS messagesSelecting the message Reading messagesSending SMS messages Calling the sender or another telephoneSender Network selection Cell Broadcast Call forwarding Call metersCall barring Fixed dial numbers Phone lockClosed user group Overview of the basic factory settings in the call menuGlossary Telephone SpecificationsAmplifier TunerIndex Index 042 175 873 Service numbersBosch Gruppe