Blaupunkt TCM 169 Operating the telephone, PIN code, Reactivating the SIM card

Page 32

Operating the telephone

General information

Using the Radiophone, you can make the same telephone calls as you can with a cel- lular phone.

Important: You must be located in an area serviced by the GSM radio network and have the access privileges provided by a valid SIM card. This SIM card must be inserted into the unit (refer to the section on “KeyCards and SIM cards” if necessary).

Emergency calls

The number to dial to place an emergency call in the GSM network anywhere in the world is 112.

You can place an emergency call by dial- ling this number even without inserting a SIM or KeyCard.

Please read the information in the section on “Using the telephone – GSM emergency calls”.

PIN code

(Personal Identification Number)

Normally, the SIM card will not operate the telephone until a personal identification number (PIN code) has been entered. This PIN code is included with the SIM card when you purchase it.

You can alter or even deactivate your PIN code. Refer to “Programming with DSC – PIN CODE”.

Inserting the SIM card/ entering your PIN code

•Switch the unit on.

With the card tongue protruding, insert the trained SIM card into the slot with the contact surface facing up.

“ENTER PIN” will appear in the display.

•Enter the PIN code using the number keys, starting with the first digit.

•Press OK or #.

If the PIN code has been entered correctly, “CODE OK” will appear in the display fol- lowed by the menu which was used last.

If an incorrect PIN code has been entered, “WRONG PIN-CODE” will appear in the dis- play followed by “ENTER PIN”.

If the PIN code is entered incorrectly three times in succession, it is necessary to use the PUK code (Personal Unblock code) to reactivate the card.

Reactivating the SIM card

The PUK code must be used to reactivate the SIM card.

The display shows “ENTER PUK”.

•Enter your code and press OK to con- firm.

•Enter a new PIN code.

Important!

Make sure you make a note of the new PIN code!

•Confirm your entry by pressing OK and repeat the entry.

96

Image 32

Contents Monte Carlo TCM Remote control RCT 07 optional Contents Radio, Cassette, Changer Option Contents Telephone Safety standards Safety informationImportant information General informationUsing the telephone while driving Using the telephone in critical areasImportant information Emergency callsInstallation AccessoriesGuarantee International telephone informa- tionStarting up the Radiophone KeyCard and SIM cardBasic information Training or replace KeyCard/ SIM card using DSC KeyCard and SIM cardRemoving the KeyCard/SIM card Train KeyCard/SIM cardsDSC learn mode Displaying the radio pass dataOptical warning of anti-theft protection Care of your KeyCard/SIM cardOn/off Volume Switching the unit on/off with the KeyCardSwitching the unit on/off via the ig- nition Switching the radio on when the ig- nition is switched offTrack switch SRC SourceTS / BND Eject cassetteCassette loading slot Storing radio stationsRecalling stored radio stations -Se AF / #= MIX DisplayRadio operation a Cassette operation Changer operation optionalStop this function by pressing or the opposite button Tape operationFlashing card tongue Additional rocker switch functions Additional settings possible with AUDDSC mode C ME Unit Corresponding function must be activatedAudio mode AF Alternative FrequencyREG regional programme Radio, tape deck, CD changer optional, auxiliary sourceStation tuning Radio operation with RDS Radio Data SystemEntering the frequency directly Selecting a wavebandScrolling through the broadcast- ing networks FM only Storing radio stationsRecalling stored radio stations Selecting the seek-tuning sensi- tivitySwitching from stereo to mono FM only Switching traffic announcement priority on/off Automatic seek tuning startSwitching off the beep tone Traffic programme station reception with RDS-EONOperating the cassette deck Operating the cassette deck Tape equalisationDolby B NR Care instructionsSelecting the CD and the track Switching CD changer operation onCD changer operation optional Cancel SelectAlter Store= ignition timer switched off Programming with DSC Radio, Cassette, Changer optionalOn All of the menu items are available Music/voice is switched offCards can only be programmed with the help of the DSC menu You can choose among the following oper- ating modes End DSC programming/save changesOverview of the DSC default settings Telephone operation Operating the telephone PIN codeInserting the SIM card/ entering your PIN code Reactivating the SIM cardOperating the telephone Making your first telephone callGSM emergency calls Do not hang up until you are told to do soQuick reference for using the telephone VolumeOn/Off Selection buttonsEnter PIN code Setup menu/Call menu To switch back to the telephone mode Press brieflyDisplays Radio menu Telephone-book menu@ Rocker switch Using the telephone GSM network service areaSwitching to telephone mode Save telephone numbers and namesUsing the telephone Dialling a telephone numberRedial function Answering/ending a callAutomatic Save telephone numbers from the note- padCall waiting 2nd caller Broker’s call/holdMaking telephone calls using the handset special accessory Setting up a conference callConference calls International callsHow to place telephone calls in foreign countries How to receive callsTeleph. number Blaupunkt You enter +49512149 TipPhone book menu 107How to enter a name/text Phone book menuFinding an entry by name Check capacity Prevent accessShow my phone number Altering, deleting, moving or copying the entry Add entryFinding an entry by position Press CL, the altered setting will not be stored Programming with DSC TelephoneStore/confirm End DSCProgramming with DSC Telephone -Setup menu Programming in the setup menuSelect the setup menu by pressing 113Ringing tone volume Automatic answer Operating mode Hands-free volumeHandset volume Automatic redialSMS tone Call meter formatAudible call timer Set charge parametersPIN code EnteredAlter access code Following settings will be deletedExternal alarm Be sure to make a note of the new code if you change itOverview of the basic factory settings in the set-up menu Extended menu Ring signalHands-free channel TA during call Hands-free operation is possible on all four channelsPress CL, the new setting will not be stored Programming with DSC Telephone -Call menuProgramming in the Call Menu 119Call mailbox Received SMS messages Selecting the messageReading messages Press OK You can display the message by press- ingSender Calling the sender or another telephoneSending SMS messages Network selection Cell Broadcast Call barring Call metersCall forwarding Phone lock Fixed dial numbersOverview of the basic factory settings in the call menu Closed user groupGlossary Specifications AmplifierTuner TelephoneIndex Index Bosch Gruppe Service numbers042 175 873