Alpine CDA-7878R owner manual Installation, Removal

Page 45

Installation

Metal plate

Detachable

Front panel

Caution

When you install this unit in your car, do not remove the Detachable Front Panel.

If the Detachable Front Panel is removed during installation, you might press too hard and warp the metal plate that holds it in place.

Caution

Do not block the unit’s fan or heat sink, thus preventing air circulation. If blocked, heat will accumulate inside the unit and may cause a fire.

Air ventilation hole

 

<Rear side>

1

Rubber Cap

 

(Included)

Bracket

Hex Bolt

 

(Included)

 

Dashboard

Mounting sleeve

(Included)

CDA-7878R

Slide mounting sleeve from main unit (see "Removal" on this page). Slide the mounting sleeve into the dashboard.

2

Metal Mounting Strap

Screw

Bolt Stud

Hex Nut (M5)

CDA-7878R

When your vehicle has the Bracket, mount the long hex bolt onto the rear panel of the CDA- 7878R and put the Rubber Cap on the hex bolt. If your vehicle does not have the Mounting Support, reinforce the head unit with the metal mounting strap (not supplied). Connect all the leads of the CDA-7878R according to details described in the CONNECTION section.

NOTE

For the screw *, provide a proper screw to the chassis installing location.

3 Slide the CDA-7878R into the dashboard. When the unit is in place, make sure the locking pins are fully seated in the down position. This can be done by pressing firmly in on the unit while pushing the locking pin down with a small screwdriver. This ensures that the unit is properly locked and will not accidentally come out from the dashboard. Install the Detachable Front Panel.

Lock pin

Removal

1 Remove the DETACHABLE FRONT PANEL.

2Use a small screwdriver (or similar tool) to push the locking pins to the “up” position (see above drawing). As each pin is unlocked, gently pull out on the unit to make sure it does not re-lock before unlocking the second pin.

3Pull the unit out, keeping it unlocked as you do so.

<JAPANESE CAR>

Face Plate

Screws (M5 8)

(Included)

CDA-7878R

Ground Lead

Mounting Bracket

NOTE

Secure the ground lead of the unit to a clean metal spot using a screw () already attached to the vehicle's chassis.

43-EN

Image 45
Contents CDA-7878R Alpine CD Changers Give You More Contents Precautions Never Attempt the Following Basic Operation Connectable to Remote Control Interface BoxDetaching the Front Panel Attaching the Front PanelDisplay Angle Adjustment Turning Power On and OffPress the Power button to turn on the unit → Balance → Fader → VolumeSUB-W Adjusting Source Signal LevelContrast AUX SUB-WSetting the Subwoofer Output Switching the Phase of the Subwoofer OutputTurning Mute Mode On/Off Sound Beep Guide FunctionScroll Setting Setting the AUX Mode V-LinkContrast SUB-W Switching the Tuner Mode DemonstrationDefeat Switching the Display Modes Blackout Mode On and OffSource SRC DHE onDisplaying the Title/Text MP3 modeSearching for Titled Discs About Title and TextErasing Disc Title Titling DiscsManual Tuning Automatic Seek TuningRadio Operation Tuning to Preset Stations Automatic Memory of Station PresetsRDS Operation Setting RDS Reception Mode and Receiving RDS StationsReceiving RDS Regional Local Stations Recalling Preset RDS StationsPTY Programme Type Tuning PI Seek SettingReceiving Traffic Information → Light M ↔ Classics ↔ Other M ←When traffic information stations cannot be received Receiving Traffic Information While Playing CD or RadioPriority PTY Programme Type Displaying Radio Text Opening and Closing the Movable display Playback→ Tuner → CD → CD CHANGER∗ Fast Forward and Backward Music Sensor SkipRepeat Play Some of the following CDs may not play on this unitCD Player Operation X. Random PlayScanning Programmes Multi-Changer Selection When a 12-disc CD Changer is connectedPlaying MP3 Files MP3 OperationFile Search Selecting FoldersWhat is MP3? Setting the Range of MP3 File SelectionAbout MP3 Method for creating MP3 filesID3 tags Supported playback sampling rates and bit ratesProducing MP3 discs Media supportedSelecting DHE Mode Adjusting the Sound OperationEqualizer Presets Selecting directlyTo store the adjusted contents Adjusting and Storing Equalizer CurveRecalling the Stored Equalizer Curve Choosing the Listening Position Selector L.P.SCrossover/Time Correction Example 2. Listening Position All Seats Example 1. Listening Position Front Left SeatAdjust the cut-off frequency/slope Adjusting and Storing the Crossover/ Time CorrectionDivider button Adjust the output level Way systemPress the Band button to select the channel to be adjusted Adjusting the Time CorrectionStoring the adjustments Direct RecallingCustomized Sound Database Controls on Remote Control Remote Control OperationRecalling Steps Operating the Audio ProcessorAdjusting/Storing the CROSSOVER/TIME Correction Battery Replacement Case of Difficulty InformationNo Magazine FM Tuner Section SpecificationsPrecautions Installation and ConnectionsRemoval InstallationTo prevent external noise from entering the audio system ConnectionsSwitched Power Lead Ignition Red Rear Output RCA Connectors Front Output RCA ConnectorsSubwoofer Output RCA Connectors Power Antenna Lead Blue RCA Extension cable Sold Separately
Related manuals
Manual 47 pages 20.51 Kb