Alpine CDA-7969R Adjusting the Time Correction, Memorizing the Time Correction Setting, 11-EN

Page 13

Adjusting the Time Correction

Time Correction:

The distance between the listener and the speakers in a car vary widely due to the special conditions of the mobile environment. This difference in the distances from the speakers to the listener creates a shift in the sounds image and frequency characteristics. This is caused by the time delay between the sound reaching the listener's right versus the left ear.

To correct this, the CDA-7969R is able to delay the audio signal to the speakers closest to the listener. This effectively creates a perception of increased distance for those speakers. The listener can be placed at an equal distance between the left and right speakers for optimum staging.

The adjustment will be made for each speaker in a step of 0.1 mS.

Example 1. Listening Position: Front Left Seat

Adjust the time correction level of the front left speaker to a high value and the rear right to zero or a low value.

0.5 m

5.1 ms

(19-11/16")

 

2.25 m

 

(88-9/16")

 

Here we calculate the time correction value for the front

right tweeter in the diagram at the left.

Conditions:

 

Farthest Speaker – listening position: 2.25 m (88-9/16")

Front right tweeter – listening postion: 0.5 m (19-11/16")

Calculation: L = 2.25 m – 0.5 m = 1.75 m (68-7/8")

Time correction = 1.75 ÷ 343* 1000 = 5.1 (ms)

*Speed of sound: 343 m/s (765 mph) at 20˚C

In other words, giving the front right tweeter a time correction value of 5.1 ms makes it seem as if the distance to the front right tweeter is the same as the distance to the farthest speaker.

The sound is not balanced because the distance between the listening position and the various speakers is different. The difference in distance between the front right speaker and the rear left speaker is 1.75 m (68-7/8").

Time correction eliminates the differences in the time required for the sound to reach the listening position.

The time of the front right speaker is corrected by 5.1 ms so that its sound reaches the listening position at the same time as the sound of other speakers.

Example 2. Listening Position: All Seats

Adjust the time correction level of each speaker to almost the same level.

1 Sit in the listening position (driver's seat, etc.) and measure the distance (in meters) between your head and the various speakers.

2 Calculate the difference between the distance to

the farthest speaker and the other speakers.

L = (distance to farthest speaker) – (distance to other speakers)

3 Divid the distances calculated for the speakers by the speed of sound (343 m/s (765 mph) at 20˚C).

These values are the time correction values for the different speakers.

4 Press the Digital Time Correction button for at least 2 seconds to switch to the Time correction adjusting mode.

5 Select a speaker to be adjusted by pressing the Preset buttons (F1 through F6) button within 10 seconds of step 4.

F1: F/L (Front Left Speaker)

F2: F/R (Front Right Speaker)

F3: R/L (Rear Left Speaker)

F4: R/R (Rear Right Speaker)

F5: S/L (Subwoofer Left)

F6: S/R (Subwoofer Right)

6 Adjust the time correction value by pressing the DN g button or the f UP button within 10 seconds of step 5.

To adjust the time correction value for other speaker, repeat the steps 5 and 6.

NOTE

The time correction setting adjusted can be memorized on memory.

Refer to "Memorizing the Time Correction Setting" on page 11.

Memorizing the Time Correction Setting

1 Adjust the time correction setting. (see this page)

2 Press the F button within 10 seconds of step 1.

3 Within 10 seconds after operating step 2, press and hold any one of the Preset buttons (F1 through F6) for at least 2 seconds. To memorize further, repeat the step 1 to 3.

Recalling the Memorized Time Correction Setting

1 Press the Digital Time Correction button to switch to the Time correction mode.

2 To recall your preset, pressing one of the Preset buttons (F1 through F6) within 10 seconds after the operation in step 1. You can recall the memorized setting.

11-EN

Image 13
Contents CDA-7969R Alpine CD Changers Give You More Contents Precautions Never Attempt the Following Basic Operation Turning Power On and OffOpening the Front Panel Hiding the Front PanelAdjusting Source Signal Level Display Angle Adjustment→ Volume → Balance → Fader Dimmer Control Changing Backlighting ColourCD Text Scroll Setting Turning Mute Mode On/OffOUT ← Close ← Demo ← AUX ← SCR ← Mute ← Switching the Display Modes Setting the AUX Mode Blackout Mode On and OffSelecting DHE Mode Adjusting the built-in Audio ProcessorAdjusting the Equalizer Settings Equalizer PresetsMemorizing the Equalizer Settings 10-ENMemorizing the Time Correction Setting Adjusting the Time CorrectionRecalling the Memorized Time Correction Setting 11-ENAutomatic Seek Tuning Manual TuningRadio Operation 12-EN13-EN Automatic Memory of Station PresetsRecalling Preset RDS Stations Setting RDS Reception Mode and Receiving RDS StationsWhen the RDS station signal received has become weak RDS OperationReceiving RDS Regional Local Stations PTY Programme Type TuningReceiving Traffic Information 15-ENReceiving Traffic Information While Playing CD or Radio When traffic information stations cannot be receivedPriority PTY Programme Type 16-ENDisplaying Radio Text Turning Emergency Alarm On or Off17-EN Opening and Closing the Movable display CD Player OperationDigital Output On and Off PlaybackFast Forward and Backward Music Sensor SkipRepeat Play X. Random PlayTitling Discs Displaying the Title/Text20-EN About Title and TextErasing Disc Title When a 12-disc CD Changer is connectedControlling CD Changer Optional 21-EN22-EN Multi-Changer SelectionControls on Remote Control Remote Control Operation23-EN 24-EN Battery ReplacementCase of Difficulty Information25-EN 26-EN HIGH-TEMP27-EN SpecificationsPrecautions Installation and Connections28-EN 29-EN InstallationRemoval 30-EN ConnectionTo prevent external noise from entering the audio system 31-EN32-EN