Alpine CDA-7969R owner manual Installation and Connections, Precautions, 28-EN

Page 30

Installation and Connections

Before installing or connecting the unit, please read the following and pages 2 and 3 of this manual thoroughly for proper use.

Warning

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire or product damage.

USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.

(Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.

The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.

USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.

Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.

BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.

Failure to do so may result in electric shock or injury due to electrical shorts.

DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS.

Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel, gear lever, brake pedals, etc. can be extremely hazardous.

DO NOT SPLICE INTO ELECTRICAL CABLES.

Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.

DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.

When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.

DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.

Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.

KEEP SMALL OBJECTS SUCH AS BATTERY OUT OF THE REACH OF CHILDREN.

Swallowing them may result in serious injury. If swallowed, consult a physician immediately.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR GEARSHIFT.

Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.

Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire's insulation from being cut by the metal edge of the hole.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.

Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.

Precautions

Be sure to disconnect the cable from the (–) battery post before installing your CDA-7969R. This will reduce any chance of damage to the unit in case of a short-circuit.

Be sure to connect the color coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage to the vehicle's electrical system.

When making connections to the vehicle's electrical system, be aware of the factory installed components (e.g. on-board computer). Do not tap into these leads to provide power for this unit. When connecting the CDA-7969R to the fuse box, make sure the fuse for the intended circuit of the CDA-7969R has the appropriate amperage. Failure to do so may result in damage to the unit and/or the vehicle. When in doubt, consult your ALPINE dealer.

The CDA-7969R uses female RCA-type jacks for connection to other units (e.g. amplifier) having RCA connectors. You may need an adaptor to connect other units. If so, please contact your authorized ALPINE dealer for assistance.

Be sure to connect the speaker (–) leads to the speaker (–) terminal. Never connect left and right channel speaker cables to each other or to the vehicle body.

IMPORTANT

Please record the serial number of your unit in the space provided below and keep it as a permanent record. The serial number plate is located on the bottom of the unit.

SERIAL NUMBER:

INSTALLATION DATE:

INSTALLATION TECHNICIAN:

PLACE OF PURCHASE:

28-EN

Image 30
Contents CDA-7969R Alpine CD Changers Give You More Contents Precautions Never Attempt the Following Opening the Front Panel Turning Power On and OffBasic Operation Hiding the Front PanelDisplay Angle Adjustment Adjusting Source Signal Level→ Volume → Balance → Fader Changing Backlighting Colour Dimmer ControlTurning Mute Mode On/Off CD Text Scroll SettingOUT ← Close ← Demo ← AUX ← SCR ← Mute ← Setting the AUX Mode Blackout Mode On and Off Switching the Display ModesAdjusting the built-in Audio Processor Selecting DHE ModeMemorizing the Equalizer Settings Equalizer PresetsAdjusting the Equalizer Settings 10-ENRecalling the Memorized Time Correction Setting Adjusting the Time CorrectionMemorizing the Time Correction Setting 11-ENRadio Operation Manual TuningAutomatic Seek Tuning 12-ENAutomatic Memory of Station Presets 13-ENWhen the RDS station signal received has become weak Setting RDS Reception Mode and Receiving RDS StationsRecalling Preset RDS Stations RDS OperationReceiving Traffic Information PTY Programme Type TuningReceiving RDS Regional Local Stations 15-ENPriority PTY Programme Type When traffic information stations cannot be receivedReceiving Traffic Information While Playing CD or Radio 16-ENTurning Emergency Alarm On or Off Displaying Radio Text17-EN Digital Output On and Off CD Player OperationOpening and Closing the Movable display PlaybackRepeat Play Music Sensor SkipFast Forward and Backward X. Random Play20-EN Displaying the Title/TextTitling Discs About Title and TextControlling CD Changer Optional When a 12-disc CD Changer is connectedErasing Disc Title 21-ENMulti-Changer Selection 22-ENRemote Control Operation Controls on Remote Control23-EN Battery Replacement 24-ENInformation Case of Difficulty25-EN HIGH-TEMP 26-ENSpecifications 27-ENInstallation and Connections Precautions28-EN Installation 29-ENRemoval Connection 30-EN31-EN To prevent external noise from entering the audio system32-EN