Sony MZ-N10 Rewriting the NV values, How to get the application NVWriter for NV values rewriting

Page 32

MZ-N10

Rewriting the NV values

Caution: The application that meets the microcomputer version in this set must be used when rewriting the NV values. Rewriting the NV values using the application not suitable for the microcomputer version could cause the set to malfunction.

For a checking method of the microcomputer version, see “SECTION 4 TEST MODE” (page 11).

• Preparation

1.USB cradle (attached to the set)

2.USB cable (attached to the set)

3.Personal computer in which the Net MD Driver has been installed. (For further information, see “System requirements” (page 4) in

“SECTION 1 SERVICING NOTES”)

4.Application “NVWriter” for NV values rewriting

• How to get the application “NVWriter” for NV values rewriting

Contact our service technical support section for PA products to get the application.

• Pre-check

1.Check the microcomputer version in this set. (For a checking method of the microcomputer version, see “SECTION 4 TEST MODE” (page 11).)

2.Check that the Net MD Driver has been installed in the personal computer.

3.Make sure that the set is in the Normal mode.

Note: Do not rewrite the NV values in the Test mode.

• Rewriting the NV values

1.Connect the USB cradle to the personal computer with the USB cable, and place the set on the USB cradle.

2.Start the application “NVWriter”.

3.Make sure that the following window opens.

4.Click the [USB CONNECT] button.

32

Image 32

Contents MZ-N10 ATRAC3 LP2/LP4Polarity of the plug On power sourcesFlexible Circuit Board Repairing Table of Contents Section Servicing Notes System requirementsRecorder Headphones/earphones with a remote control Section GeneralSection Disassembly Equipment can be removed using the following procedureBottom Panel Section, Jog Dial Section Upper Panel SectionMain Board Section MD Mechanism Deck MT-MZN10-181, Set ChassisOP Service Assy ABX-1R Gear SA, Gear SBHolder Assy Section Test Mode Setting Method of Test ModeOperation in Setting the Test Mode Releasing the Test ModeConfiguration of Test Mode Manual ModeTransition method in manual mode A n u a l011 C 6 8 S 0 F F J 0011 0 6 3 B 0 011 0 5 9 a 0R r C L R Reset the Error Display CodeL r O K ? 000 P * * R 000000 FF 000 rFFRMC OK 000 JOG+000 JOG+OK 000 JOGReset ResNV CCResOK? 021 ResPower Supply Manual Adjustment 741 VC1 L742 VC1 H 743 VC2 Lo747 REG3L1 748 REG3L2749 REG3 H Vrec LVrec H 754 3.3upcChgV L ChgV HTP1907 REG3 TP1909 REG1 Power Supply Adjustment Auto Item Feed Configuration of power supply adjustment auto item feedAssy ADJ OKLaser LrefPw @HrefPw @ WrPwLo @Configuration of overall adjustment mode Adjusted values modifying procedure881 ###S 882 ###SAssy11 000 *** NGCD OK MO OKMO overall adjustment items Resume clear setting method Resume043 Res ResClrRewriting the Patch Data at Replacement of Main Board PreparationPre-check Rewriting the patch dataMZ-N10 Confirmation of contents of the patch data rewrited Removing the set Rewriting the NV values How to get the application NVWriter for NV values rewritingRewriting the NV values MZ-N10 MZ-N10 MZ-N10 043 Remaining charging time Number of times of fully chargingSection Diagrams Block DiagramWaveforms 4Vp-pPrinted Wiring Board Main Board Side a Uses unleaded solder Semiconductor LocationMain Board Side B Uses unleaded solder Main BoardSchematic Diagrams Main Board 1/4 See page 38 for Waveforms C513 270 ∝H TC7SZ126AFE IC Block Diagrams IC302 AN17020A-VBIC502 XC62HR2202MR IC503 XC62HR2502MR IC862 R2061K01-E2 IC951 SC901582EPR2 IC Pin Function Description Sens FmckXskh XsklFfclr XcsnvJoga JogbUosci UoscoSI3 SO3Xras XCSDVSS0 DVSS1Msak FVDD0FVSS0 Section Exploded Views KNOB, Balance White . . . REDBottom Panel Section US,CND,HK,KR,TW,E18,CHChassis Section 111 112 106 105 104 103MD Mechanism Deck Section MT-MZN10-181 152 153 151Main Electrical Parts List SectionMain CAP,CHIP Ceramic Resistor Switch 501 502 505504 503 507Memo Revision History Date Description of Revision