Sony Ericsson LBI-38965 installation manual Hardware Installation

Page 18

LBI-38965

4. INSTALLATION

4.1. HARDWARE INSTALLATION

CAUTION

Turn off the power before removing or installing VMEbus boards. Removing or reinstalling the boards while the power is on will damage the boards.

This section describes the physical installation of the BCU/CAL. Other configuration is performed during manufacture, and the information necessary is provided in Appendix B.

Follow these steps to connect a BCU/CAL to an IMC for the first time (except where indicated otherwise, these steps apply to all configurations; BCU only, CAL only, or BCU and CAL):

Using the LAPB cable provided, connect the BCU/CAL's CAM control port 0, a female DB-25 connector located on the rear of the BCU enclosure, to the lower connector on the IMC backplane which corresponds to the slot in which the CAM resides. The cable is keyed so that it fits properly only when it is correctly oriented.

BCU/CAL Equipment Rack

			852327G1
	BCU/CAL
			J1
			J1
	CAM Control		J14
	Port 0		J14
	Port 0

Data Concentrator at BCU/CAL Equipment Rack

IMC Equipment Rack

	903531P1			19D903628P71
	903531P1					P72
		P2		P1		P73
	J1	P2		P1		P73
						CAM Control


	J9			This will be plugged into
				PA2XX on the backplane
				and will correspond with
				the slot in which the CAM
	Audio Concentrator			the slot in which the CAM
	Audio Concentrator			control card is located.

at IMC

19D903880P120-129

Figure 5 - BCU/CAL to IMC

Next, connect the console terminal to the female DB-25 connector labeled "SERIAL PORT 1/CONSOLE" on the TVME-712/M transition module located in the rear of the BCU/CAL enclosure. (For reference, the BCU/CAL is delivered preconfigured from the factory in a 19-inch rack.) Connect the other end of this cable to the console terminal's "host" port, or equivalent. If a PC is used as the console terminal, then a DB-9 adapter may be needed. In either case, the serial cable for the console is wired straight-through.

Configure the console terminal for the communications parameters below.

∙9600 Baud

∙No Parity

∙8 Data Bits

∙1 Stop Bit

18

Image 18

Contents System and Installation Manual Table of Contents LBI-38965Table of Contents Introduction BCU/CAL ArchitectureBCU Functional Description CAL Functional DescriptionCall Types Supported Physical Specifications Physical Description and CompatibilityBCU/CAL Architecture TVME147 CPUCPU Compatibility Backwards CompatibilitySpecifications Common BCU and CAL Operational SpecificationsBCU Operational Specifications Billing Architecture Billing Architecture BCU Operation OverviewConversations Group Billing ModeRF Channel Usage Air Time Grouping CallsFile Name Contents Database Elements Default DataOperator Functions Unit DataCDR Processing CDR Processing ErrorsCall Processing Call Processing CDR OutputCAL Operational Specifications System Manager InterfaceProtocol Supported Additional Product Features Network File System CAL Operation OverviewInstallation Hardware InstallationSoftware Installation Installation Contents DisketteFile Name Usage Parameter MeaningEXPORTS.DAT Configuration File ParameterCAL.DAT Configuration File Directory Clientip EXPORTS.DAT File ParametersCAL.DAT File Parameters SITE01Initial Installation PrerequisitesInstallation Return First-Time Configuration Default System AccountsLogin Password Access Level Prerequisite User Information Entering bcs invokes the BCS programSystem Disk Booting Proper System Shutdown User Information Invoke the BCS programCAL Terminal Server Configuration Software UpgradesExample Configuration Tips Page Appendix a Edacs Billing CDR Format Billing for Multiple Sites OverviewBilling by Conversation Record EncodingMULTIPLE-SITE Calls Record LayoutSINGLE-SITE Calls MOBILE-TO-LAND Telephone Interconnect CallsTable A.1 Call Detail Record Field Descriptions Name Size Format Range/Values DescriptionCall Type Definitions Table A.2 Call TypesCall Type Description Valid with Hex Decimal Rec. Type A0-FF Call Type Bit Fields Table A.3 Call Type Bit Field DefinitionsCDR File Topics Appendix B Physical Configuration Details Jumper Settings Figure B.1 Tvme 147SA1 Single-Board Computer Figure B.2 Tvme 712/M Transition Module Figure B.4 fv5310 Main Board Figure B.5 fv5310 Mezzanine Card Scsi Connector Pwr Table B.1 WANServer Port DB-25F Signal Name Function ConnectorCable Pinouts Table B.2 WANServer PortTable B.3 WANServer Port Table B.4 WANServer PortTable B.5 BCU/CAL Hdlc Loopback Cable Specification DB-25M Connector Signal Name Function BCU/CAL PortFigure B.9 CAL Terminal Server to Distribution Panel Cable A14 INM AC H106 Computer Terminal Appendix C Fault Tolerance Figure C.1 Edacs Billing Fault Tolerant Architecture Redundant Operation