Sears 831.29776 user manual Symptom the Pulse Sensor does not Function Properly

Page 21

c. Error code "E4" may appear in the SPEED display if the walking belt is moving at a slow speed, and there is " excessive stress on the motor. Remove the key, wait for ten seconds, and then reinsert it. If youweigh over

200pounds, it may be helpful to increase the incline of the treadmill. If the error code appears again, call our toll-free Customer Service Department. Do not operate the treadmill until the problem is corrected.

d.Error code "E5" may appear in the PULSE display if a pulse error occurs. See HOW TO USE THE PULSE

SENSOR on page 8, and PULSE DISPLAY on page 12.

5.SYMPTOM: THE PULSE SENSOR DOES NOT FUNCTION PROPERLY

a. See HOW TO USE THE PULSE SENSOR on page 8, and PULSE DISPLAY on page 12.

6.SYMPTOM: THE WALKING BELT IS OFF-CENTER WHEN WALKED ON

a. If the walking belt has shifted to the left, first remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn the left rear roller adjustment bolt clockwise 114of a turn. Plug in the power cord, insert the key and run the treadmill for a few min- utes. Repeat until the walking belt is centered.

b. If the walking belt has shifted to the dght, first remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn the left rear roller adjustment bolt counterclockwise 1/4 of a turn. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is centered.

a

b

7.SYMPTOM: THE TREADMILL SITS UNEVENLY ON THE FLOOR

a. Make sure that the six base pads are attached to the treadmill. See assembly step 2 on page 6.

21

Image 21
Contents Performancetreadmill Model No Serial NoSEARS, Roebuck and CO., Hoffman ESTATES, IL Full 90 DAY Warranty Table of ContentsImportant Precautions Awarning Thank you for selecting the Proform = 725 TL tread Before YOU BeginWater Bottle Holder Foot Rails Front WheelAssembly Refer to HOW to Lower the Treadmill for USEOn page 19. Follow the instructions to lower the treadmill Make sure that the sensor window is pressed through Attach the Pulse Sensor 114 to the Head6and 114 I \HOW to USE the Pulse Sensor HOW to Plug Power Cord Operation AdjustmentPerformant Lube TM Walking Belt Having an equipment-grounding conductor and aIagramoftheconsole Features of the ConsoleHOW Touse Emanualmode WeightUAL Control AGEPulse dlsplay For this display to op Erate, the pulse sen Sor must be worn see Pulse Sensor on8. After a few Seconds, the heart WeHr a MancePressed, Time display =r,s j Mcoe Ness TestFIT Ness Test USE the PulseHOW to Select the Information Mode Cate your relative fitSpond while the Fitness Test program is selected HOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Remove the Cover Panel Latch.1 Closed Frame Cover Panel FastenerHOW to Move the Treadmill HOW to Lower the Treadmill for USEStorage Closed Symptom the Power Turns OFF During USE Symptom the Power does not Turn onSymptom the Walking Belt Slows When Walked on PositionSymptom the Pulse Sensor does not Function Properly Symptom the Walking Belt is OFF-CENTER When Walked onSymptom the Treadmill Sits Unevenly on the Floor Conditioning Guidelines Exercise IntensityWorkout Guidelines Correct form for several basic stretches is shown Suggested StretchesPage Remove this Exploded Drawing and Part List from the Manual 131 \115 100 Fastener NSPModel No SE /ARS