JVC RX-5060B manual is in use Adjustable when Pro Logic II Music is in use

Page 105

Adjusting Sound

You can make sound adjustment to your preference after completing basic settings.

Basic Adjustment Items

On the following pages, you can adjust the following items:

•You can adjust only the items applicable to the current sound mode.

Items	To do	See page
DEQ 63HZ	Adjust equalizer pattern at 63 Hz.		25

DEQ250HZ	Adjust equalizer pattern at 250 Hz.		25

DEQ 1KHZ	Adjust equalizer pattern at 1 kHz.		25

DEQ 4KHZ	Adjust equalizer pattern at 4 kHz.		25

DEQ16KHZ	Adjust equalizer pattern at 16 kHz.		25

SUBWFR LEVEL	Adjust the subwoofer output level.		25

FRONT L LEVEL	Adjust the left front speaker output
	level.		25

FRONT R LEVEL	Adjust the right front speaker output
	level.		25

CENTER LEVEL	Adjust the center speaker output
	level.		25

SURR L LEVEL	Adjust the left surround speaker
	output level.		25

SURR R LEVEL	Adjust the right surround speaker
	output level.		25

EFFECT*1	Adjust the effect level.		25
CENTER TONE	Make the center tone soft or sharp.		25

PANORAMA CTRL*2 Add “wraparound” sound effect with
	side-wall image.		25

Basic Procedure	Remote
	NOT

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

Ex. When adjusting the subwoofer level to “–3.”

1 Press ADJUST.

The last selected item appears on the display.

2Turn MULTI JOG until an item you want appears on the display.

•In this example, select “SUBWFR LEVEL.” For available items, see the list “Basic Adjustment Items.”

			3	Press in MULTI JOG (PUSH SET).
Notes:				The current setting (or level) for the selected item appears on the
*1	Adjustable when one of the DAP modes or Mono Film (see pages			display.
*1
	29 and 30) is in use.
*2	Adjustable when Pro Logic II Music is in use.

			4	Turn MULTI JOG to select a setting you want or
				to make an adjustment as you like.

5 Press in MULTI JOG (PUSH SET).

6 Repeat steps 2 to 5 to set other items if necessary.

7 Press EXIT.

The source indication resumes on the display.

24

Image 105

Contents RX-5060B For U.S.A Mises en garde, précautions et indications diversesTable of Contents Parts Identification Front PanelDisplay Rear Panel Remote ControlConnecting the FM and AM Antennas Before InstallationChecking the Supplied Accessories Putting Batteries in the Remote ControlConnecting the Speakers and Subwoofer Connecting the speakersAM antenna connections Connecting the subwoofer Connecting Audio/Video ComponentsPlacing speakers Analog ConnectionsVCR Video component connectionsConnecting the Power Cord Plug the power cord into an AC outletDigital Connections Turning On the Power Daily Operational Procedure Selecting the Source to PlayTo turn off the power into standby mode Basic OperationsWhen analog input is selected Always lights up Adjusting the VolumeSound Picture from a video component such as the VCR or DVDSelecting the Analog or Digital Input Mode Listening with headphonesPress Subwoofer OUT ON/OFF to cancel the subwoofer output To select the analog input mode When Dolby Digital or DTS Surround is selectedChanging the Display Brightness Press DimmerBasic adjustment auto memory Using the Sleep TimerMuting the Sound Recording a sourceUsing Preset Tuning Tuning in to Stations ManuallyTo erase a stored preset station Receiving Radio BroadcastsTo tune in a preset station Selecting the FM Reception ModeBefore you start, remember Basic SettingsSize of the connected speakers Room Speaker Distance Output SizeEx. When setting Virtual Surround Back to Vrtl SB on Basic Setting ItemsSetting the Speakers Setting the Speaker DistanceSetting the Bass Sounds Select the playback sounds channel Selecting the Main or Sub ChannelSetting the Digital Input Terminals Setting for Effective Surround OperationsSelect Vrtl SB on to activate Virtual Surround Back Set the components connected to the digital terminalsAdjusting Sound Basic Adjustment ItemsEx. When adjusting the subwoofer level to Adjusting the Speaker Output Levels Adjusting the Equalization PatternsReproducing Theater Ambience Introducing the Surround Modes Using the Surround ModesDolby Digital*1 Dolby Digital 5.1CHWhat is Dual Mono? What is Linear PCM?DTS Digital Surround DTS 96/24Activating the Surround Modes To cancel the Surround modeAuto Surround Function Activating the Surround Modes ManuallyReproducing the Sound Field Using the DSP ModesIntroducing the DSP Modes Digital Acoustic Processor DAP modesMulti-channel digital signals To cancel the DSP modeActivating the DSP Modes All Channel StereoRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingOperating Audio Components Operating JVC’s Audio/Video ComponentsCD changer Operating Video ComponentsDVD player Set TV/CATV selector to TVIf there are more than one code listed for your brand of TV Operating Other Manufacturers’ Video EquipmentManufacturer Codes Operating Other Manufacturers’ Video Equipment If there are more than one code listed for your brandProblem Possible Cause Solution TroubleshootingOutput Power SpecificationsAmplifier AudioFM tuner IHF AM tunerGeneral Page Page AUDIO/VIDEO Control Receiver Recepteur DE Commande AUDIO/VIDEO Mises en garde, précautions et indications diverses English Basic Settings4 5 6 7 8 9 0 = ~ Enter Level DVD Do not insert any metal object into the receiver Speakersleft Getting Started VCR Connecting the Power Cord Basic Operations Basic Operations Turning On and Off Attenuating the Input Signal When playing software encoded with Dolby Digital or DTS,Following symptoms may occur OFFCanceled Tuning in to Stations Manually Selecting the FM Reception Mode Basic Settings Basic Procedure Basic Settings Selecting the Main or Sub Channel Setting for Effective Surround Operations Display Current setting or level for the selected item appears onAdjusting Sound Using the Surround Modes Using the Surround Modes Auto SURROUND* Plii Game Using the DSP Modes Activating the DSP Modes Compu Link Remote Control System Operating JVC’s Audio/Video Components Operating JVC’s Audio/Video Components Operating Other Manufacturers’ Video Equipment Operating Other Manufacturers’ Video Equipment Troubleshooting Front channels EN, FR RX-5062S If in Doubt Consult a Competent Electrician RX-5062S Above ALL Information for Users on Disposal of Old EquipmentTroubleshooting Specifications Basic Settings 4 5 6 7 8 9 0 = ~ ! @ Display Mode Remote Control Batteries AM MW Loop Antenna FM Antenna Connecting the FM and AM MW AntennasAntenna supplied AM MW antenna connectionsGetting Started VCR Connecting the Power Cord TAPE/CDR DVD AUX FM/AM Basic Operations For details about the digital signal formats, see pages 26 Attenuating the Input Signal Muting the Sound Receiving Radio Broadcasts Selecting the FM Reception Mode Receiving FM Stations with Radio Data System To show the Radio Data System informationEnhanced Other Networks Searching for a Program by PTY Codes To search for a program using the PTY codesTo continue searching after the first stop Description of the PTY codes News NewsSwitching to a Program of Your Choice Automatically When the current source is FMWhen the current source is other than FM LS/RS These items can be set using Quick Speaker Setup see Setting the Speakers Selecting the Main or Sub Channel Setting for Effective Surround Operations 30 is in use Adjustable when Pro Logic II Music is in use Adjusting the Equalization Patterns Using the Surround Modes DTS*2 Using the Surround Modes Using the DSP Modes Using the DSP Modes Operating JVC’s Audio/Video Components TV CH + Troubleshooting AM MW tuner RX-5062S