JVC RX-5060B manual Tape/Cdr Dvd Aux Fm/Am

Page 90

Basic Operations

The following operations are commonly used when you play any sound sources.

Operations hereafter will be explained using the buttons on the front panel.

You can also use the buttons on the remote control for the same functions if they have the same and similar names/marks.

Daily Operational Procedure

Selecting the Source to Play

1Turn on the power.

•See “Turning On the Power” below.

2Select the source.

•See “Selecting the Source to Play” to the right.

3Adjust the volume.

•See “Adjusting the Volume” on page 10.

4Select the Surround or DSP modes.

•See “Activating the Surround Modes” (page 28) and “Activating the DSP Modes” (page 30).

Turning On the Power

Press STANDBY/ON (or STANDBY/ON AUDIO on the remote control).

The STANDBY lamp goes off.

Current source name appears.

VOLUME

Current volume level appears.

To turn off the power (into standby mode),

press STANDBY/ON (or STANDBY/ON AUDIO on the remote control) again.

The STANDBY lamp lights up.

Note:

A small amount of power is consumed in standby mode. To turn off

the power completely, unplug the AC power cord.

When you have connected digital source components using the digital terminals, first change the input mode for these components to the digital input mode (see page 11).

Press one of the source selection buttons.

Selected source name appears.

VOLUME

AUX	DVD	VCR	TV SOUND	CD	TAPE/CDR	FM	AM
					SOURCE NAME
		On the front panel
		TAPE/CDR	CD	DVD	AUX
		FM/AM	TV SOUND	VCR

On the remote control

Notes:

•When connecting a CD recorder to the TAPE/CDR jacks, change the source name shown on the display. For details, see page 12.

•By pressing the one of the audio source selection buttons—TAPE/ CDR, CD, and FM/AM—on the remote control, you can turn on the receiver and select the audio source.

9

Image 90

Contents RX-5060B Mises en garde, précautions et indications diverses For U.S.ATable of Contents Parts Identification Front PanelDisplay Remote Control Rear PanelChecking the Supplied Accessories Before InstallationConnecting the FM and AM Antennas Putting Batteries in the Remote ControlConnecting the Speakers and Subwoofer Connecting the speakersAM antenna connections Placing speakers Connecting Audio/Video ComponentsConnecting the subwoofer Analog ConnectionsVideo component connections VCRConnecting the Power Cord Plug the power cord into an AC outletDigital Connections To turn off the power into standby mode Daily Operational Procedure Selecting the Source to PlayTurning On the Power Basic OperationsSound Adjusting the VolumeWhen analog input is selected Always lights up Picture from a video component such as the VCR or DVDSelecting the Analog or Digital Input Mode Listening with headphonesPress Subwoofer OUT ON/OFF to cancel the subwoofer output Changing the Display Brightness When Dolby Digital or DTS Surround is selectedTo select the analog input mode Press DimmerMuting the Sound Using the Sleep TimerBasic adjustment auto memory Recording a sourceTo erase a stored preset station Tuning in to Stations ManuallyUsing Preset Tuning Receiving Radio BroadcastsSelecting the FM Reception Mode To tune in a preset stationSize of the connected speakers Basic SettingsBefore you start, remember Room Speaker Distance Output SizeBasic Setting Items Ex. When setting Virtual Surround Back to Vrtl SB onSetting the Speakers Setting the Speaker DistanceSetting the Bass Sounds Selecting the Main or Sub Channel Select the playback sounds channelSelect Vrtl SB on to activate Virtual Surround Back Setting for Effective Surround OperationsSetting the Digital Input Terminals Set the components connected to the digital terminalsAdjusting Sound Basic Adjustment ItemsEx. When adjusting the subwoofer level to Adjusting the Equalization Patterns Adjusting the Speaker Output LevelsDolby Digital*1 Using the Surround ModesReproducing Theater Ambience Introducing the Surround Modes Dolby Digital 5.1CHDTS Digital Surround What is Linear PCM?What is Dual Mono? DTS 96/24Auto Surround Function To cancel the Surround modeActivating the Surround Modes Activating the Surround Modes ManuallyIntroducing the DSP Modes Using the DSP ModesReproducing the Sound Field Digital Acoustic Processor DAP modesActivating the DSP Modes To cancel the DSP modeMulti-channel digital signals All Channel StereoAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingOperating JVC’s Audio/Video Components Operating Audio ComponentsDVD player Operating Video ComponentsCD changer Set TV/CATV selector to TVIf there are more than one code listed for your brand of TV Operating Other Manufacturers’ Video EquipmentManufacturer Codes If there are more than one code listed for your brand Operating Other Manufacturers’ Video EquipmentTroubleshooting Problem Possible Cause SolutionAmplifier SpecificationsOutput Power AudioFM tuner IHF AM tunerGeneral Page Page AUDIO/VIDEO Control Receiver Recepteur DE Commande AUDIO/VIDEO Mises en garde, précautions et indications diverses Basic Settings English4 5 6 7 8 9 0 = ~ Enter Level DVD Do not insert any metal object into the receiver Speakersleft Getting Started VCR Connecting the Power Cord Basic Operations Basic Operations Turning On and Off Attenuating the Input Signal When playing software encoded with Dolby Digital or DTS,Following symptoms may occur OFFCanceled Tuning in to Stations Manually Selecting the FM Reception Mode Basic Settings Basic Procedure Basic Settings Selecting the Main or Sub Channel Setting for Effective Surround Operations Current setting or level for the selected item appears on DisplayAdjusting Sound Using the Surround Modes Using the Surround Modes Auto SURROUND* Plii Game Using the DSP Modes Activating the DSP Modes Compu Link Remote Control System Operating JVC’s Audio/Video Components Operating JVC’s Audio/Video Components Operating Other Manufacturers’ Video Equipment Operating Other Manufacturers’ Video Equipment Troubleshooting Front channels EN, FR RX-5062S If in Doubt Consult a Competent Electrician RX-5062S Information for Users on Disposal of Old Equipment Above ALLTroubleshooting Specifications Basic Settings 4 5 6 7 8 9 0 = ~ ! @ Display Mode Connecting the FM and AM MW Antennas Remote Control Batteries AM MW Loop Antenna FM AntennaAM MW antenna connections Antenna suppliedGetting Started VCR Connecting the Power Cord TAPE/CDR DVD AUX FM/AM Basic Operations For details about the digital signal formats, see pages 26 Attenuating the Input Signal Muting the Sound Receiving Radio Broadcasts Selecting the FM Reception Mode Receiving FM Stations with Radio Data System To show the Radio Data System informationEnhanced Other Networks To continue searching after the first stop To search for a program using the PTY codesSearching for a Program by PTY Codes Description of the PTY codes News NewsSwitching to a Program of Your Choice Automatically When the current source is FMWhen the current source is other than FM LS/RS These items can be set using Quick Speaker Setup see Setting the Speakers Selecting the Main or Sub Channel Setting for Effective Surround Operations 30 is in use Adjustable when Pro Logic II Music is in use Adjusting the Equalization Patterns Using the Surround Modes DTS*2 Using the Surround Modes Using the DSP Modes Using the DSP Modes Operating JVC’s Audio/Video Components TV CH + Troubleshooting AM MW tuner RX-5062S