JVC RX-5060B manual Troubleshooting

Page 114

Troubleshooting

Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC’s service center.

 

PROBLEM

POSSIBLE CAUSE

SOLUTION

 

 

 

 

 

The display does not light up.

The power cord is not plugged in.

Plug the power cord into an AC outlet.

 

 

 

 

 

No sound from speakers.

Speaker signal cables are not

Check speaker wiring and reconnect if necessary.

 

 

connected.

(See page 5.)

 

 

 

 

 

 

The SPEAKERS ON/OFF button is

Press SPEAKERS ON/OFF so that the sounds

 

 

not set correctly.

come out of the speakers. (See page 11.)

 

 

 

 

 

 

An incorrect source is selected.

Select the correct source.

 

 

 

 

 

 

Muting is activated.

Press MUTING to cancel the mute. (See page 13.)

 

 

 

 

 

 

An incorrect input mode (analog or

Select the correct input mode (analog or digital).

 

 

digital) is selected.

(See pages 11 and 12.)

 

 

 

 

 

“NO SUBWOOFER” appears on the

The SUBWOOFER OUT ON/OFF

If subwoofer is connected, set “SUBWOOFER

 

display.

button is pressed while

YES” so that the SUBWOOFER OUT ON/OFF

 

 

“SUBWOOFER” is set to

button works.

 

 

“SUBWOOFER NO.”

 

 

 

 

 

 

Continuous hiss or buzzing during FM

Incoming signal is too weak.

Connect an outdoor FM antenna or contact your

 

reception.

 

dealer. (See page 4.)

 

 

 

 

 

 

The station is too far away.

Select a new station.

 

 

 

 

 

Noise is heard during FM/AM (MW)

An incorrect antenna is used.

Check with your dealer to be sure you have the

 

reception.

 

correct antenna.

 

 

 

 

 

 

Antennas are not connected properly.

Check connections. (See pages 4 and 5.)

 

 

 

 

 

 

Ignition noise from automobiles.

Move the antenna farther from automobile traffic.

 

 

 

 

 

“OVERLOAD” starts flashing on the

Speakers are overloaded because of

1. Press STANDBY/ON on the front panel to

 

display.

high volume.

turn off the receiver.

 

 

 

2. Stop the playback source.

 

 

 

3. Turn on the receiver again, and adjust the

 

 

 

volume.

Speakers are overloaded because of short circuit of speaker terminals.

Press STANDBY/ON on the front panel to turn off the receiver, then check the speaker wiring.

If “OVERLOAD” does not disappear, unplug the AC power cord, then plug it back again.

If speaker wiring is not short-circuited, contact your dealer.

“DSP NG” appears on the display.

The built-in microcomputer is not functioning correctly.

Press STANDBY/ON on the front panel to turn off the receiver. After unplugging the AC power cord, contact your dealer.

The STANDBY lamp lights up after turning on the power, and soon the receiver turns off again (into standby mode).

The receiver is overloaded because of a high voltage.

Press STANDBY/ON on the front panel to turn off the receiver. After unplugging the AC power cord, contact your dealer.

Remote control does not work.

There is an obstruction between the

Remove the obstruction.

remote sensor on the receiver and the

 

remote control.

 

Batteries are weak.

Replace batteries. (See page 4.)

Remote control does not work as you intend.

An incorrect remote control operation mode is selected.

Select the correct remote control operation mode. (See pages 31 and 32.)

33

Page 113 Page 115
Image 114
Page 113 Page 115
Contents RX-5060B Mises en garde, précautions et indications diverses For U.S.ATable of Contents Parts Identification Front PanelDisplay Remote Control Rear PanelChecking the Supplied Accessories Before InstallationConnecting the FM and AM Antennas Putting Batteries in the Remote ControlConnecting the Speakers and Subwoofer Connecting the speakersAM antenna connections Placing speakers Connecting Audio/Video ComponentsConnecting the subwoofer Analog ConnectionsVideo component connections VCRConnecting the Power Cord Plug the power cord into an AC outletDigital Connections To turn off the power into standby mode Daily Operational Procedure Selecting the Source to PlayTurning On the Power Basic OperationsSound Adjusting the VolumeWhen analog input is selected Always lights up Picture from a video component such as the VCR or DVDSelecting the Analog or Digital Input Mode Listening with headphonesPress Subwoofer OUT ON/OFF to cancel the subwoofer output Changing the Display Brightness When Dolby Digital or DTS Surround is selectedTo select the analog input mode Press DimmerMuting the Sound Using the Sleep TimerBasic adjustment auto memory Recording a sourceTo erase a stored preset station Tuning in to Stations ManuallyUsing Preset Tuning Receiving Radio BroadcastsSelecting the FM Reception Mode To tune in a preset stationSize of the connected speakers Basic SettingsBefore you start, remember Room Speaker Distance Output SizeBasic Setting Items Ex. When setting Virtual Surround Back to Vrtl SB onSetting the Speakers Setting the Speaker DistanceSetting the Bass Sounds Selecting the Main or Sub Channel Select the playback sounds channelSelect Vrtl SB on to activate Virtual Surround Back Setting for Effective Surround OperationsSetting the Digital Input Terminals Set the components connected to the digital terminalsAdjusting Sound Basic Adjustment ItemsEx. When adjusting the subwoofer level to Adjusting the Equalization Patterns Adjusting the Speaker Output LevelsDolby Digital*1 Using the Surround ModesReproducing Theater Ambience Introducing the Surround Modes Dolby Digital 5.1CHDTS Digital Surround What is Linear PCM?What is Dual Mono? DTS 96/24Auto Surround Function To cancel the Surround modeActivating the Surround Modes Activating the Surround Modes ManuallyIntroducing the DSP Modes Using the DSP ModesReproducing the Sound Field Digital Acoustic Processor DAP modesActivating the DSP Modes To cancel the DSP modeMulti-channel digital signals All Channel StereoAutomatic Source Selection Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Synchronized RecordingOperating JVC’s Audio/Video Components Operating Audio ComponentsDVD player Operating Video ComponentsCD changer Set TV/CATV selector to TVIf there are more than one code listed for your brand of TV Operating Other Manufacturers’ Video EquipmentManufacturer Codes If there are more than one code listed for your brand Operating Other Manufacturers’ Video EquipmentTroubleshooting Problem Possible Cause SolutionAmplifier SpecificationsOutput Power AudioFM tuner IHF AM tunerGeneral Page Page AUDIO/VIDEO Control Receiver Recepteur DE Commande AUDIO/VIDEO Mises en garde, précautions et indications diverses Basic Settings English4 5 6 7 8 9 0 = ~ Enter Level DVD Do not insert any metal object into the receiver Speakersleft Getting Started VCR Connecting the Power Cord Basic Operations Basic Operations Turning On and Off Attenuating the Input Signal When playing software encoded with Dolby Digital or DTS,Following symptoms may occur OFFCanceled Tuning in to Stations Manually Selecting the FM Reception Mode Basic Settings Basic Procedure Basic Settings Selecting the Main or Sub Channel Setting for Effective Surround Operations Current setting or level for the selected item appears on DisplayAdjusting Sound Using the Surround Modes Using the Surround Modes Auto SURROUND* Plii Game Using the DSP Modes Activating the DSP Modes Compu Link Remote Control System Operating JVC’s Audio/Video Components Operating JVC’s Audio/Video Components Operating Other Manufacturers’ Video Equipment Operating Other Manufacturers’ Video Equipment Troubleshooting Front channels EN, FR RX-5062S If in Doubt Consult a Competent Electrician RX-5062S Information for Users on Disposal of Old Equipment Above ALLTroubleshooting Specifications Basic Settings 4 5 6 7 8 9 0 = ~ ! @ Display Mode Connecting the FM and AM MW Antennas Remote Control Batteries AM MW Loop Antenna FM AntennaAM MW antenna connections Antenna suppliedGetting Started VCR Connecting the Power Cord TAPE/CDR DVD AUX FM/AM Basic Operations For details about the digital signal formats, see pages 26 Attenuating the Input Signal Muting the Sound Receiving Radio Broadcasts Selecting the FM Reception Mode Receiving FM Stations with Radio Data System To show the Radio Data System informationEnhanced Other Networks To continue searching after the first stop To search for a program using the PTY codesSearching for a Program by PTY Codes Description of the PTY codes News NewsSwitching to a Program of Your Choice Automatically When the current source is FMWhen the current source is other than FM LS/RS These items can be set using Quick Speaker Setup see Setting the Speakers Selecting the Main or Sub Channel Setting for Effective Surround Operations 30 is in use Adjustable when Pro Logic II Music is in use Adjusting the Equalization Patterns Using the Surround Modes DTS*2 Using the Surround Modes Using the DSP Modes Using the DSP Modes Operating JVC’s Audio/Video Components TV CH + Troubleshooting AM MW tuner RX-5062S
Top Page Image Contents