JVC RX-5060B manual Selecting the FM Reception Mode

Page 57

To tune in a preset station

On the front panel:

1Press FM or AM to select the band.

2Press FM/AM PRESET 5 or until you find the channel you want.

Pressing FM/AM PRESET 5 increases the number.

Pressing FM/AM PRESET ∞ decreases the number.

On the remote control:

1 2 3

4 5 6

7 8 9

1010

TA/NEWS/INFO

REWFF

REC PAUSE

CD-DISC

 

 

FM/AM

1 Press FM/AM to select the band (FM or AM).

The last received station of the selected band is tuned in.

Each time you press the button, the band alternates between FM and AM.

2Press the number buttons to select a preset channel number.

For channel number 5, press 5.

For channel number 15, press +10 then 5.

For channel number 20, press +10 then 10.

For channel number 30, press +10, +10, then 10.

Note:

When you use the number buttons on the remote control, be sure that they are activated for the tuner, not for the CD and others. (See page 29.)

Selecting the FM Reception Mode

When an FM stereo broadcast is hard to receive or noisy, you can change the FM reception mode while receiving an FM broadcast.

You can store the FM reception mode for each preset station (see page 14).

While listening to an FM station, press FM MODE.

Each time you press the button, the FM reception mode alternates between “AUTO MUTING” and “MODE MONO.”

TUNED STEREO AUTO MUTING

AUTO MUTING

 

MODE MONO

 

AUTO MUTING: Normally select this.

When a program is broadcasted in stereo, you will hear stereo sound; when in monaural, you will hear monaural sounds. This mode is also useful to suppress static noise between stations.

The AUTO MUTING indicator lights up on the display. (Initial setting)

MODE MONO: Select this to improve the reception (but stereo effect will be lost).

In this mode, you will hear noise while tuning in to the stations.

The AUTO MUTING indicator goes off from the display. (The STEREO indicator also goes off.)

Note:

After you operate any source other than the tuner using the remote control, the FM MODE button on the remote control does not work. In this case, press FM/AM on the remote control, then press FM MODE.

English

15

Image 57
Contents RX-5060B For U.S.A Mises en garde, précautions et indications diversesTable of Contents Parts Identification Front PanelDisplay Rear Panel Remote ControlConnecting the FM and AM Antennas Before InstallationChecking the Supplied Accessories Putting Batteries in the Remote ControlConnecting the Speakers and Subwoofer Connecting the speakersAM antenna connections Connecting the subwoofer Connecting Audio/Video ComponentsPlacing speakers Analog ConnectionsVCR Video component connectionsConnecting the Power Cord Plug the power cord into an AC outletDigital Connections Turning On the Power Daily Operational Procedure Selecting the Source to PlayTo turn off the power into standby mode Basic OperationsWhen analog input is selected Always lights up Adjusting the VolumeSound Picture from a video component such as the VCR or DVDSelecting the Analog or Digital Input Mode Listening with headphonesPress Subwoofer OUT ON/OFF to cancel the subwoofer output To select the analog input mode When Dolby Digital or DTS Surround is selectedChanging the Display Brightness Press DimmerBasic adjustment auto memory Using the Sleep TimerMuting the Sound Recording a sourceUsing Preset Tuning Tuning in to Stations ManuallyTo erase a stored preset station Receiving Radio BroadcastsTo tune in a preset station Selecting the FM Reception ModeBefore you start, remember Basic SettingsSize of the connected speakers Room Speaker Distance Output SizeEx. When setting Virtual Surround Back to Vrtl SB on Basic Setting ItemsSetting the Speakers Setting the Speaker DistanceSetting the Bass Sounds Select the playback sounds channel Selecting the Main or Sub ChannelSetting the Digital Input Terminals Setting for Effective Surround OperationsSelect Vrtl SB on to activate Virtual Surround Back Set the components connected to the digital terminalsAdjusting Sound Basic Adjustment ItemsEx. When adjusting the subwoofer level to Adjusting the Speaker Output Levels Adjusting the Equalization PatternsReproducing Theater Ambience Introducing the Surround Modes Using the Surround ModesDolby Digital*1 Dolby Digital 5.1CHWhat is Dual Mono? What is Linear PCM?DTS Digital Surround DTS 96/24Activating the Surround Modes To cancel the Surround modeAuto Surround Function Activating the Surround Modes ManuallyReproducing the Sound Field Using the DSP ModesIntroducing the DSP Modes Digital Acoustic Processor DAP modesMulti-channel digital signals To cancel the DSP modeActivating the DSP Modes All Channel StereoRemote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingOperating Audio Components Operating JVC’s Audio/Video ComponentsCD changer Operating Video ComponentsDVD player Set TV/CATV selector to TVIf there are more than one code listed for your brand of TV Operating Other Manufacturers’ Video EquipmentManufacturer Codes Operating Other Manufacturers’ Video Equipment If there are more than one code listed for your brandProblem Possible Cause Solution TroubleshootingOutput Power SpecificationsAmplifier AudioFM tuner IHF AM tunerGeneral Page Page AUDIO/VIDEO Control Receiver Recepteur DE Commande AUDIO/VIDEO Mises en garde, précautions et indications diverses English Basic Settings4 5 6 7 8 9 0 = ~ Enter Level DVD Do not insert any metal object into the receiver Speakersleft Getting Started VCR Connecting the Power Cord Basic Operations Basic Operations Turning On and Off Attenuating the Input Signal When playing software encoded with Dolby Digital or DTS,Following symptoms may occur OFFCanceled Tuning in to Stations Manually Selecting the FM Reception Mode Basic Settings Basic Procedure Basic Settings Selecting the Main or Sub Channel Setting for Effective Surround Operations Display Current setting or level for the selected item appears onAdjusting Sound Using the Surround Modes Using the Surround Modes Auto SURROUND* Plii Game Using the DSP Modes Activating the DSP Modes Compu Link Remote Control System Operating JVC’s Audio/Video Components Operating JVC’s Audio/Video Components Operating Other Manufacturers’ Video Equipment Operating Other Manufacturers’ Video Equipment Troubleshooting Front channels EN, FR RX-5062S If in Doubt Consult a Competent Electrician RX-5062S Above ALL Information for Users on Disposal of Old EquipmentTroubleshooting Specifications Basic Settings 4 5 6 7 8 9 0 = ~ ! @ Display Mode Remote Control Batteries AM MW Loop Antenna FM Antenna Connecting the FM and AM MW AntennasAntenna supplied AM MW antenna connectionsGetting Started VCR Connecting the Power Cord TAPE/CDR DVD AUX FM/AM Basic Operations For details about the digital signal formats, see pages 26 Attenuating the Input Signal Muting the Sound Receiving Radio Broadcasts Selecting the FM Reception Mode Receiving FM Stations with Radio Data System To show the Radio Data System informationEnhanced Other Networks Searching for a Program by PTY Codes To search for a program using the PTY codesTo continue searching after the first stop Description of the PTY codes News NewsSwitching to a Program of Your Choice Automatically When the current source is FMWhen the current source is other than FM LS/RS These items can be set using Quick Speaker Setup see Setting the Speakers Selecting the Main or Sub Channel Setting for Effective Surround Operations 30 is in use Adjustable when Pro Logic II Music is in use Adjusting the Equalization Patterns Using the Surround Modes DTS*2 Using the Surround Modes Using the DSP Modes Using the DSP Modes Operating JVC’s Audio/Video Components TV CH + Troubleshooting AM MW tuner RX-5062S