4.Slide both of the Electronics Ground Brackets (14) onto one of the Handrail Spacers (65) in the manner shown.
See inset drawing A. Pinch the tabs on the Electronics Ground Brackets (14) to allow the tabs to fit inside the holes in the Upright (69, see inset drawing B).
See inset drawing B. Place the Handrail Spacer (65) on
the left Upright (69) as shown, with the cutout on the indi- cated side. Note: Make sure that the tabs on the
Electronics Ground Brackets (14, see inset drawing A) are inserted into the holes in the Upright.
5.Pull the Upright Wire Harness (98) up through the other Handrail Spacer (65). Place the Handrail Spacer on the right Upright (69) as shown, with the cutout on the indi- cated side (see inset drawing A).
Have a second person hold the Handrails (66) near the Uprights (69) as shown. Connect the Upright Wire Harness (98) to the wires extending from the Console Base (81). Insert the connectors and the Upright Wire Harness into the hole in the Console Base (see inset drawing B).
Being careful not to pinch the Upright Wire Harness (98), set the Handrails (66) on the Handrail Spacers (65).
6.Insert two Handrail Bolts (78) with Handrail Washers
(77)and Handrail Bushings (75) into the right Upright
(69)and the right Handrail Spacer (65). Turn the Handrail Bushings so they fit against the Upright with the thick sides of the Bushings toward the center of the treadmill as shown in the inset drawing. Lift the right Handrail (66) to align the Bolts with the holes in the
Handrail. Next, thread the Bolts into the Handrail. | Do |
not tighten the Bolts yet. |
|
Attach the left Handrail (not shown) in the same way. |
|
Tighten all four Handrail Bolts (78). |
|
4 | 14 | A |
|
|
|
65 |
| Tabs |
| ||
|
|
|
| ||
|
| 14 |
|
|
|
B |
|
|
| Cutout |
|
|
|
|
|
| |
| 65 |
|
|
| 69 |
|
|
|
|
| |
5 |
| Cutout | A |
|
|
|
| 81 |
|
|
|
|
| 66 |
|
| 69 |
|
|
|
|
| |
|
|
|
|
| 65 |
|
| 98 69 | B | 98 |
|
| 65 |
|
|
|
|
|
|
|
|
| 81 |
6 |
|
|
|
|
|
|
| 66 |
| ||
|
| 65 |
|
|
|
|
| 69 |
|
| |
|
|
|
| 75 | Thick |
|
|
|
| 77 | |
|
|
|
| Side | |
|
|
|
|
| |
|
| 75 |
|
|
|
|
| 77 |
| 78 |
|
7. Make sure that all parts are tightened before you use the treadmill. | Note: If there is a thin sheet of clear | |
plastic on the face of | the hood decal and the “ComforTrack” decal, remove it. | Keep the included allen wrench in |
a secure place. The allen wrench is used to adjust the walking belt (see page 27). To protect the floor or car- pet from damage, place a mat under the treadmill.
7