Reebok RCTL07809.0 manual Raise the Frame 53 to the position shown

Page 13

14.Raise the Frame (53) to the position shown.

Have a second person hold the Frame until this step is completed.

Orient the Storage Latch (50) so that the large barrel and the Latch Knob (51) are in the posi- tions shown.

Remove the tie from the upper end of the Storage Latch (50). Attach the upper end of the Storage Latch to the bracket on the Frame (53) with a 3/8" x 2" Bolt (3) and a 3/8" Locknut (11). Remove the tie from the lower end of the Storage Latch (50). Keep the holes in the Latch Cap (49) aligned with the holes in the Storage Latch. Make sure to keep the Latch Cap in- side the Storage Latch. Attach the Storage Latch to the bracket on the Base (60) with a 3/8" x 1 3/4" Bolt (8). Note: It may be necessary to move the Frame (53) back and forth to align the Storage Latch with the bracket.

Lower the Frame (53) (see HOW TO LOWER THE TREADMILL FOR USE on page 21).

14
11	53
11
3
50
51
Large
Barrel
60
49	8

15.Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread- mill. Note: Extra hardware may be included. Keep the included hex keys in a secure place; one of the hex keys is used to adjust the walking belt (see pages 23 and 24).

13

Image 13

Contents Contact OUR Customer SER Vice Department Directly QUESTIONS?Table of Contents Important Precautions Treadmill, and before performing the mainte Power cord, and switch the reset/off cirCuit breaker to the off position when Treadmill is not in use. See the drawing onBefore YOU Begin Assembly Do not fully fold the Frame yet Make sure that the power cord is unpluggedOvertighten the Locknut the Wheel must Turn freely Right Upright do not fully tighten the Bolts Yet With a second Bolt Spacer 84, 3/8 x 4 Bolt 3/8 Star WasherBolts yet Attach the other resistance mechanism to 3/4 Bolt 112. Do not fully tighten Resistance KnobRight Upright 79 as described above Attach the other Crosswalk Arm 98 as dePower Again. if the Connectors are not CONCareful not to pinch the wires Be careful not to pinch the wires in the Right Handrail Raise the Frame 53 to the position shown HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerSelect the manual mode Insert the key into the consoleTurn on the fan if desired Measure your heart rate if desired. Before usingSelect one of the preset workouts. To select one HOW to USE a Preset WorkoutInsert an iFit card and select a workout HOW to USE AN Ifit WorkoutHOW to USE the Stereo Sound System Information ModeHOW to USE the Crosswalk Arms HOW to Fold the Treadmill for Storage HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USEProblem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Problem The walking belt slows when walked on Reed Switch is about 1/8 in mm. If necTop Make sure that the gap between the MagnetProblem Solution Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencyR1009A Part LIST-Model No. RCTL07809.0110 Resistance Knob Userʼs Manual Exploded Drawing A-Model No. RCTL07809.0 R1009A Exploded Drawing B-Model No. RCTL07809.0 R1009A Exploded Drawing C-Model No. RCTL07809.0 R1009A Exploded Drawing D-Model No. RCTL07809.0 R1009A Limited Warranty Ordering Replacement Parts