Reebok RCTL07809.0 manual Top, Make sure that the gap between the Magnet

Page 23

Remove the three #8 x 3/4" Screws (1) and care- fully pivot the Motor Hood (63) off.

63 1

Locate the Reed Switch (68) and the Magnet (48)

 

 

on the left side of the Pulley (47). Turn the Pulley

Top

 

until the Magnet is aligned with the Reed Switch.

 

Make sure that the gap between the Magnet and

View

 

the Reed Switch is about 1/8 in. (3 mm). If nec-

1/8 in.

 

essary, loosen the 3/4" Screw (16), move the Reed

 

Switch slightly, and then retighten the Screw.

68

48

Reattach the Motor Hood (not shown) with the #8 x

 

47

3/4" Screws (not shown). Reattach the #8 x 2"

 

Screws (not shown) if necessary. Run the treadmill

 

 

for a few minutes to check for a correct speed

 

 

reading.

 

 

PROBLEM: The incline of the treadmill does not change correctly

 

 

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 14.

b. If the walking belt is overtightened, treadmill perfor-

b

 

mance may decrease and the walking belt may be-

2–3 in.

come damaged. Remove the key and UNPLUG

 

THE POWER CORD. Using the hex key, turn both

 

 

idler roller bolts counterclockwise, 1/4 of a turn.

 

 

When the walking belt is properly tightened, you

 

 

should be able to lift each edge of the walking belt

 

 

2 to 3 in. (5 to 7 cm) off the walking platform. Be

 

 

careful to keep the walking belt centered. Then,

 

 

plug in the power cord, insert the key, and run the

 

 

treadmill for a few minutes. Repeat until the walking

Idler Roller Bolts

belt is properly tightened.

c. If the walking belt still slows when walked on, see the front cover of this manual.

23

Image 23
Contents Contact OUR Customer SER Vice Department Directly QUESTIONS?Table of Contents Important Precautions Treadmill is not in use. See the drawing on Power cord, and switch the reset/off cirTreadmill, and before performing the mainte Cuit breaker to the off position whenBefore YOU Begin Assembly Overtighten the Locknut the Wheel must Turn freely Make sure that the power cord is unpluggedDo not fully fold the Frame yet Right Upright do not fully tighten the Bolts Yet With a second Bolt Spacer 84, 3/8 x 4 Bolt 3/8 Star WasherBolts yet Attach the other Crosswalk Arm 98 as de 3/4 Bolt 112. Do not fully tighten Resistance KnobAttach the other resistance mechanism to Right Upright 79 as described aboveCareful not to pinch the wires Again. if the Connectors are not CONPower Be careful not to pinch the wires in the Right Handrail Raise the Frame 53 to the position shown PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Console DiagramInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Select the manual modeTurn on the fan if desired Measure your heart rate if desired. Before usingSelect one of the preset workouts. To select one HOW to USE a Preset WorkoutInsert an iFit card and select a workout HOW to USE AN Ifit WorkoutHOW to USE the Crosswalk Arms Information ModeHOW to USE the Stereo Sound System HOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillCompatible with GFCI-equipped outlets TroubleshootingProblem The power turns off during use Make sure that the gap between the Magnet Reed Switch is about 1/8 in mm. If necProblem The walking belt slows when walked on TopProblem Solution Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesR1009A Part LIST-Model No. RCTL07809.0110 Resistance Knob Userʼs Manual Exploded Drawing A-Model No. RCTL07809.0 R1009A Exploded Drawing B-Model No. RCTL07809.0 R1009A Exploded Drawing C-Model No. RCTL07809.0 R1009A Exploded Drawing D-Model No. RCTL07809.0 R1009A Limited Warranty Ordering Replacement Parts