Reebok RCTL07809.0 manual Troubleshooting, Compatible with GFCI-equipped outlets

Page 22

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 14). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 14. IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch

 

protrudes as shown, the circuit breaker has

 

 

tripped. To reset the circuit breaker, wait for five

Tripped

Reset

minutes and then press the switch back in.

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c.Remove the key from the console. Reinsert the key into the console.

d.If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a

store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off

the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE

INFORMATION MODE on page 20 to turn off the demo mode.

 

PROBLEM: The displays of the console do not function properly

 

 

SOLUTION: a. Remove the key from the console and UNPLUG

a

77

THE POWER CORD. With the help of a second

person, carefully tip the Uprights (77, 79) down.

 

 

There may be three #8 x 2" Screws (24) in the bot-

 

 

tom of the Belly Pan (70). If there are, remove

 

 

them. Note: A Phillips screwdriver with a shaft at

 

70

least 5 in. (13 cm) long is required. Then, raise the

79

Uprights.

 

 

 

24

 

 

24

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents QUESTIONS? Contact OUR Customer SER Vice Department DirectlyTable of Contents Important Precautions Cuit breaker to the off position when Power cord, and switch the reset/off cirTreadmill, and before performing the mainte Treadmill is not in use. See the drawing onBefore YOU Begin Assembly Do not fully fold the Frame yet Make sure that the power cord is unpluggedOvertighten the Locknut the Wheel must Turn freely With a second Bolt Spacer 84, 3/8 x 4 Bolt 3/8 Star Washer Right Upright do not fully tighten the Bolts YetBolts yet Right Upright 79 as described above 3/4 Bolt 112. Do not fully tighten Resistance KnobAttach the other resistance mechanism to Attach the other Crosswalk Arm 98 as dePower Again. if the Connectors are not CONCareful not to pinch the wires Be careful not to pinch the wires in the Right Handrail Raise the Frame 53 to the position shown HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleSelect the manual mode HOW to Turn on the PowerHOW to USE the Manual Mode Insert the key into the consoleMeasure your heart rate if desired. Before using Turn on the fan if desiredHOW to USE a Preset Workout Select one of the preset workouts. To select oneHOW to USE AN Ifit Workout Insert an iFit card and select a workoutHOW to USE the Stereo Sound System Information ModeHOW to USE the Crosswalk Arms HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Lower the Treadmill for USEProblem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Top Reed Switch is about 1/8 in mm. If necProblem The walking belt slows when walked on Make sure that the gap between the MagnetProblem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart LIST-Model No. RCTL07809.0 R1009A110 Resistance Knob Userʼs Manual Exploded Drawing A-Model No. RCTL07809.0 R1009A Exploded Drawing B-Model No. RCTL07809.0 R1009A Exploded Drawing C-Model No. RCTL07809.0 R1009A Exploded Drawing D-Model No. RCTL07809.0 R1009A Ordering Replacement Parts Limited Warranty
Top Page Image Contents