Reebok RCTL07809.0 manual Problem Solution

Page 24

PROBLEM:

SOLUTION:

PROBLEM:

SOLUTION:

The walking belt is off-center or slips when walked on a. If the walking belt is off-center, first remove the

key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left idler roller bolt clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the bolt counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walk- ing belt is centered.

b. If the walking belt slips when walked on, first re- move the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller bolts clock- wise, 1/4 of a turn. When the walking belt is cor- rectly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walk- ing belt centered. Then, plug in the power cord, in- sert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

The crosswalk arms squeak during use

a. (Note: Correcting this problem requires a small amount of white marine grease, available at hard- ware stores.) Turn the Resistance Knob (110) counterclockwise and remove it. Next, remove the Resistance Cone (108) with the Crosswalk Arm (98).

Apply a thin layer of white marine grease to the outer surface of the Resistance Cone (108). Then, reattach the Resistance Cone with the Crosswalk Arm (98) and the Resistance Knob (110).

a

b

a

98

 

110

108

24

Image 24
Contents QUESTIONS? Contact OUR Customer SER Vice Department DirectlyTable of Contents Important Precautions Power cord, and switch the reset/off cir Treadmill, and before performing the mainteCuit breaker to the off position when Treadmill is not in use. See the drawing onBefore YOU Begin Assembly Make sure that the power cord is unplugged Do not fully fold the Frame yetOvertighten the Locknut the Wheel must Turn freely With a second Bolt Spacer 84, 3/8 x 4 Bolt 3/8 Star Washer Right Upright do not fully tighten the Bolts YetBolts yet 3/4 Bolt 112. Do not fully tighten Resistance Knob Attach the other resistance mechanism toRight Upright 79 as described above Attach the other Crosswalk Arm 98 as deAgain. if the Connectors are not CON PowerCareful not to pinch the wires Be careful not to pinch the wires in the Right Handrail Raise the Frame 53 to the position shown Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeSelect the manual mode Insert the key into the consoleMeasure your heart rate if desired. Before using Turn on the fan if desiredHOW to USE a Preset Workout Select one of the preset workouts. To select oneHOW to USE AN Ifit Workout Insert an iFit card and select a workoutInformation Mode HOW to USE the Stereo Sound SystemHOW to USE the Crosswalk Arms HOW to Fold and Move the Treadmill HOW to Fold the Treadmill for StorageHOW to Move the Treadmill HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useCompatible with GFCI-equipped outlets Reed Switch is about 1/8 in mm. If nec Problem The walking belt slows when walked onTop Make sure that the gap between the MagnetProblem Solution Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart LIST-Model No. RCTL07809.0 R1009A110 Resistance Knob Userʼs Manual Exploded Drawing A-Model No. RCTL07809.0 R1009A Exploded Drawing B-Model No. RCTL07809.0 R1009A Exploded Drawing C-Model No. RCTL07809.0 R1009A Exploded Drawing D-Model No. RCTL07809.0 R1009A Ordering Replacement Parts Limited Warranty