Gold's Gym GGTL07809.0 manual Troubleshooting, Important The treadmill is not

Page 25

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 14). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 14.

IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the reset/off circuit breaker located on the

c

 

treadmill frame near the power cord. If the switch pro-

 

trudes as shown, the circuit breaker has tripped. To

 

 

reset the circuit breaker, wait for five minutes and

Tripped

Reset

then press the switch to the reset position.

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait for five minutes and then press the switch to the reset position.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c. Remove the key from the console. Reinsert the key into the console. d. If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The console displays remain lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a

store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off

the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE

INFORMATION MODE on page 22 to turn off the demo mode.

 

PROBLEM: The displays of the console do not function properly

a

 

SOLUTION: a. Remove the key from the console and UNPLUG THE

77

POWER CORD. Lower the Uprights (77).

 

Next, remove the two indicated #8 x 3/4" Screws (1).

 

 

Raise the Uprights (77).

 

1

 

77

 

1

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Model No. GGTL07809.0 Serial No QUESTIONS?Table of Contents Important Precautions Page Before YOU Begin Assembly Not fully fold the Frame until the treadmill is Make sure that the power cord is unpluggedCompletely assembled Tek Screws 4 do not overtighten the TekFully tighten the Patch Bolts yet See the inset drawing. Tie the wire tiePage Repeat this step with the Right Handrail Cover Console assembly. See the inset drawingPatch Bolts before tightening any of them Uprights. Be careful not to pinch any wires104 Page HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerInsert the key into the console Follow your progress with the displays. The matrix-When you Turn on the fans if desired Measure your heart rate if desired. Before usingSelect a preset workout HOW to USE a Preset WorkoutStart the walking belt Select a custom workout HOW to Create a Custom WorkoutHOW to USE a Custom Workout HOW to USE the Stereo Sound System Information ModeMake sure that the audio wire is fully plugged HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingImportant The treadmill is not Compatible with GFCI-equipped outletsTop Problem The walking belt slows when walked onWalking belt is off-center or slips when walked on Problem SolutionExercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencyKey No. Qty Description Part LIST-Model No. GGTL07809.0Qty Exploded Drawing A-Model No. GGTL07809.0 R0909A Exploded Drawing B-Model No. GGTL07809.0 R0909A Exploded Drawing C-Model No. GGTL07809.0 R0909A Exploded Drawing D-Model No. GGTL07809.0 R0909A Exploded Drawing E-Model No. GGTL07809.0 R0909A Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents