Gold's Gym GGTL07809.0 See the inset drawing. Tie the wire tie, Fully tighten the Patch Bolts yet

Page 8

3. Identify the right Upright (77), which is marked

3

76

 

 

Plate

 

 

 

 

with a sticker. Have a second person hold the

 

 

77

 

 

right Upright near Base (83). Orient the right

 

 

 

 

 

83

 

Upright so that the bend in the plate is in the po-

 

 

Wire

 

 

 

 

 

sition shown.

 

 

 

 

 

 

 

 

See the inset drawing. Tie the wire tie in the

 

 

Tie

 

 

 

 

 

 

right Upright (77) securely around the end of the

 

 

 

 

 

 

 

 

 

Upright Wire (76). Then, pull the other end of

 

 

 

 

 

 

 

 

 

the wire tie until the Upright Wire is routed com-

 

 

 

 

 

 

 

 

 

pletely through the right Upright.

 

 

 

 

 

 

 

 

 

 

77

76

 

 

 

 

 

 

 

 

Wire Tie

 

 

 

 

 

 

 

4. Attach the right Upright (77) to the Base (83)

4

 

 

 

 

 

 

 

 

with a 3/8" x 2 3/4" Patch Bolt (7), a 3/8" x 1"

 

 

 

 

 

 

 

 

Patch Bolt (8), and two 3/8" Star Washers (11);

 

 

 

 

77

 

76

 

 

do not fully tighten the Patch Bolts yet. Be

 

 

 

 

 

83

 

careful not to pinch the Upright Wire (76).

 

 

 

 

 

 

 

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

7

5. With the help of a second person, carefully tip

5

 

 

 

 

 

 

 

 

the treadmill onto its right side. Partially fold the

 

 

 

Plate

 

 

 

Frame (51) so the treadmill is more stable. Do

 

 

 

 

 

 

 

not fully fold the Frame until the treadmill is

 

11

83

77

 

 

 

 

 

completely assembled.

 

 

 

 

 

 

Orient the left Upright (77) so that the bend in

 

 

 

 

 

 

 

 

 

the plate is in the position shown.

 

 

 

 

 

 

 

 

 

Attach the left Upright (77) to the Base (83) with

7

8

 

 

 

 

 

7

 

a 3/8" x 2 3/4" Patch Bolt (7), a 3/8" x 1" Patch

 

 

 

 

 

 

Bolt (8), and two 3/8" Star Washers (11); do not

 

 

 

 

 

 

 

 

 

fully tighten the Patch Bolts yet.

 

 

 

 

88

 

 

 

 

Attach a Wheel (91) to the indicated Extension

 

 

 

 

91

 

 

 

Leg (88) with a 3/8" x 2 3/4" Patch Bolt (7) and a

 

 

 

 

 

 

 

 

3/8" Nut (12). Do not overtighten the Nut; the

 

 

 

 

 

 

12

51

 

Wheel must turn freely.

 

 

 

 

 

 

 

With the help of a second person, tip the tread-

 

 

 

 

 

 

 

 

 

mill so that the Base (83) is flat on the floor.

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Image 8
Contents QUESTIONS? Model No. GGTL07809.0 Serial NoTable of Contents Important Precautions Page Before YOU Begin Assembly Make sure that the power cord is unplugged Not fully fold the Frame until the treadmill isCompletely assembled Tek Screws 4 do not overtighten the TekSee the inset drawing. Tie the wire tie Fully tighten the Patch Bolts yetPage Console assembly. See the inset drawing Repeat this step with the Right Handrail CoverUprights. Be careful not to pinch any wires Patch Bolts before tightening any of them104 Page PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleInsert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Follow your progress with the displays. The matrix-When you Measure your heart rate if desired. Before using Turn on the fans if desiredStart the walking belt HOW to USE a Preset WorkoutSelect a preset workout HOW to Create a Custom Workout Select a custom workoutHOW to USE a Custom Workout Make sure that the audio wire is fully plugged Information ModeHOW to USE the Stereo Sound System HOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useImportant The treadmill is not Compatible with GFCI-equipped outletsProblem The walking belt slows when walked on TopProblem Solution Walking belt is off-center or slips when walked onExercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart LIST-Model No. GGTL07809.0 Key No. Qty DescriptionQty Exploded Drawing A-Model No. GGTL07809.0 R0909A Exploded Drawing B-Model No. GGTL07809.0 R0909A Exploded Drawing C-Model No. GGTL07809.0 R0909A Exploded Drawing D-Model No. GGTL07809.0 R0909A Exploded Drawing E-Model No. GGTL07809.0 R0909A Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty