NordicTrack NTL19806.0 user manual Problem The walking belt slows when walked on

Page 27

Next, locate the Reed Switch (14) and the Magnet

(12)on the left side of the Pulley (11). Turn the Pulley until the Magnet is aligned with the Reed Switch.

Make sure that the gap between the Magnet and the Reed Switch is about 1/8”. If necessary, loosen the indicated Screw (29), move the Reed Switch slightly, and then retighten the Screw. Then, reattach the hood, and run the treadmill for a few minutes to check for a correct speed reading.

Top

 

View

 

29

1/8”

14

11

12

 

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 13.

b. If the walking belt is overtightened, treadmill perfor- mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

b

3”–4”

 

Rear Roller Bolts

c. If the walking belt still slows when walked on, please see the front cover of this manual.

PROBLEM: The walking belt is off-center or slips when walked on

SOLUTION: a. If the walking belt is off-center, remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left rear roller bolt clockwise 1/2 of a turn; if the walk- ing belt has shifted to the right, turn the left rear roller bolt counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered.

b.If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened.

a

b

27

Image 27 Contents
QUESTIONS? Model No. NTL19806.0 Serial NoCall TOLL-FREE Table of Contents Important Precautions Page Power Lines Before YOU Begin Assembly Ful not to pinch the Upright Wire Harness Make sure that no wires are pinched Page HOW to Connect a DVD Player or VCR HOW to Connect AN AntennaHOW to Connect a 75 OHM Catv Cable HOW to Connect a VCRChest Pulse Sensor Care and Maintenance HOW to USE the Chest Pulse SensorHOW to PUT on the Chest Pulse Sensor Chest Pulse Sensor TroubleshootingOperation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramChange the incline of the treadmill as desired HOW to Turn on the Power HOW to USE the Manual ModeSelect the manual mode Start the walking belt and adjust the speedMeasure your heart rate if desired Turn on the fan if desiredWhenkey. you are finished exercising, remove HOW to USE AN Event Training Program Select an event training programPress the Start button to start the program HOW to USE a Preset Program Select a preset programEnter your weight Select one of the four custom programs HOW to Create a Custom ProgramHOW to USE a Custom Program HOW to USE a Heart Rate Program Press the Channel buttons to select Desired channel HOW to Operate the Personal TelevisionPress the Volume buttons to adjust the volume HOW to USE the Stereo Sound System Press the TV button again and add or delete Channels HOW to USE the Information ModeHOW to Adjust the Cushioning System HOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill for Storage HOW to Move the TreadmillProblem The power turns off during use TroubleshootingProblem The walking belt slows when walked on Problem The chest pulse sensor does not function properly Problem Television reception is poorExercise Frequency Conditioning GuidelinesExercise Intensity Workout GuidelinesQty Description R1006AOrdering Replacement Parts Model No. NTL19806.0 No. NTL19806.0 Limited Warranty