Bowflex 3000 If Calibration Fails Screen Displays Cal Fail Message, If calibration is successful

Page 23

Assembly

If Calibration Fails (Screen Displays “Cal Fail” Message):

This error usually indicates that the console is unable to determine the speed of the belts. Take the following steps:

1.Unplug the unit and remove the three back covers.

2.Hold a stiff business card, ID card, or other similar onto the inside of the drive pulley. Adjust the speed sensor to- wards the card until it just makes contact.

3.Remove the card.

4.Plug unit in and recalibrate.

If calibration is successful:

• Replace the three back covers.

If calibration is not successful:

•Leave plastic covers off and contact customer care for assistance. ( See Important Contact Numbers page at the back of this manual).

Explanation of Calibration Display Messages (for information only):

During calibration, the TIME display will show you text messages updating you as to the status of calibration. When there is no text message in the TIME display window, the other displays will show the following:

HEART RATE (TC5000 Only) – will show the status of the motor control relay.

•“ON” signifies the power relay is on and energizing the motor.

•“OFF” signifies the motor control relay is off and not energizing the motor.

CALORIES/CAL PER MIN – will show the version number of the software.

TIME – will show either a text message regarding auto-calibration (“d0nE”, “Strt”, etc.) or the actual Pulse Width Modulation (PWM) number (a number that provides digital information about base unit functions to the console) if START/STOP, FASTER or SLOWER is pressed during calibration.

MILES/TOTAL STEPS (DISTANCE/MILES for TC3000) – will show the calibration of the total step count. SPEED – will display the actual belt speed during the calibration function.

Assembly Manual

19

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Bowflex TreadClimber 1000, 3000 Page Table of Contents Page TC1000 TC3000 Product SpecificationsObey the following warnings Important Safety InstructionsSelect Your Workout Area Basic Assembly PrinciplesBefore You Assemble Box 1 contains PartsBox 2 contains the TreadClimber treadles Qty1 Assembly Hardware BagContains the following Hardware Hardware8 X 1 1/4 Hex Bolts preassembled AssemblyTreadClimber Base Assembly TreadClimber Treadle Assembly Put the Treadles on the BaseSpeed Wire Connect the Speed and Step Wires TC3000 and TC5000 onlyAttach the Drive Belt TreadClimber Base and Treadle assembly from Step Drive BeltLock the Treadles 16 x 1 Button Head Screws Attach the UprightsAttach the Upright Junction 16 x 1 Button Head Screws 16 Flat Washers SAE Attach the Console Handlebar AssemblyHex Key included Open End Wrench included TreadClimber Base and Treadle assembly from StepAttach the Cosmetic Plugs Attach the Hydraulic Cylinders#10 Phillips Head Screws Inspect the AssemblyAttach the Frame Covers TreadClimber Base and Treadle assembly from Step Rear Cover Adjust Speed Sensor and Attach the Rear Cover 4 x 1 Flat Head Screws Attach the Drive Covers Attach the Side Foot Support Platforms #2 Phillips Head Screwdriver includedApply Decals Attach the Power CordCalibration TC3000 and TC5000 only Main Power Switch OnIf calibration is not successful If Calibration Fails Screen Displays Cal Fail MessageIf calibration is successful Replace the three back coversTroubleshooting Drive belt Unplug power from unit. Wait 5-minutes to Sion should be adjusted. If both belts stop butBe adjusted Ments, stop and refer to drive belt checklistConnection of speed sensor to jumper wire Mill modeBelt drive line. Using a ½ wrench, tighten Diagnostics on control boardExploded Views TC1000 Console AssemblyOrdering Replacement Parts Walking Belts Rear Belt Guide Right Drive Cover Page United States Offices Important Contact NumbersNautilus Bowflex Schwinn Fitness StairMaster Universal
Top Page Image Contents