Bowflex 5000, 1000, 3000 manual Contains the following, Qty1 Assembly Hardware Bag

Page 9

Parts

Box 1 also contains:

Qty:1 Owner’s Manual Bag

Contains the following:

•The Bowflex® TreadClimber® Assembly Guide and Owner’s Manual

•(1) Drive Belt

•Power Cord

•(2) Treadle Decals

•(2) Drive Cover Decals

•TreadClimber® Safety Key *Note: TC1000 Safety Key plugged into console for shipping.

•Heart Rate Monitor Chest Strap (TC5000 Only)

•(1) #2 Phillips Screw Driver

Note: Occasionally extra parts are included.

Qty:1 Assembly Hardware Bag

Contains the following:

•(1) #2 Phillips Screwdriver

•(2) 5/16" x 1 1/2" Button Head Screw

•(1) 3/16" Hex Key

•(12) 5/16" Flat Washers SAE (smaller O.D.)

•(1) 5/32" Hex Key

•(2) 5/16" Acorn Nut

•(1) 9/16" Open End Wrench

•(6) 1/4" x 1" Flat Head Screw

•(2) 5/16" Flat Washers

•(4) 3/8" Cosmetic Plugs

•(14) 5/16" x 1" Button Head Screw

•(16) #10 Phillips

Box 2 contains the TreadClimber® treadles

Cylinder Stud

Qty: 1

Descr: TreadClimber® Treadle Assembly

Box 3 contains the TreadClimber® base
Qty: 1
Descr: TreadClimber® Base
Assembly Manual	5

Image 9

Contents Bowflex TreadClimber 1000, 3000 Page Table of Contents Page TC1000 TC3000 Product Specifications Obey the following warnings Important Safety InstructionsBasic Assembly Principles Before You AssembleSelect Your Workout Area Box 1 contains PartsQty1 Assembly Hardware Bag Contains the followingBox 2 contains the TreadClimber treadles Hardware HardwareTreadClimber Base Assembly TreadClimber Treadle Assembly AssemblyPut the Treadles on the Base 8 X 1 1/4 Hex Bolts preassembledSpeed Wire Connect the Speed and Step Wires TC3000 and TC5000 onlyTreadClimber Base and Treadle assembly from Step Drive Belt Lock the TreadlesAttach the Drive Belt 16 x 1 Button Head Screws Attach the UprightsAttach the Upright Junction 16 x 1 Button Head Screws 16 Flat Washers SAE Attach the Console Handlebar AssemblyAttach the Cosmetic Plugs TreadClimber Base and Treadle assembly from StepAttach the Hydraulic Cylinders Hex Key included Open End Wrench includedInspect the Assembly Attach the Frame Covers#10 Phillips Head Screws TreadClimber Base and Treadle assembly from Step Rear Cover Adjust Speed Sensor and Attach the Rear CoverAttach the Side Foot Support Platforms Attach the Drive Covers#2 Phillips Head Screwdriver included 4 x 1 Flat Head ScrewsApply Decals Attach the Power CordCalibration TC3000 and TC5000 only Main Power Switch OnIf calibration is successful If Calibration Fails Screen Displays Cal Fail MessageReplace the three back covers If calibration is not successfulTroubleshooting Be adjusted Sion should be adjusted. If both belts stop butMents, stop and refer to drive belt checklist Drive belt Unplug power from unit. Wait 5-minutes toBelt drive line. Using a ½ wrench, tighten Mill modeDiagnostics on control board Connection of speed sensor to jumper wireTC1000 Console Assembly Ordering Replacement PartsExploded Views Walking Belts Rear Belt Guide Right Drive Cover Page United States Offices Important Contact NumbersNautilus Bowflex Schwinn Fitness StairMaster Universal