Gold's Gym GGSY3066.1 manual Do not tighten the Nylon Locknuts yet, Nylon Locknut yet

Page 9

Frame Assembly

1

 

 

 

 

 

 

 

1.

 

 

 

 

Before beginning assembly, make sure that

 

 

 

 

you understand the information in the box

 

 

 

 

on page 8. See the PART IDENTIFICATION

 

 

 

 

CHART on pages 5–7 for help identifying

 

 

 

 

small parts.

 

 

1

83

 

 

 

Insert four M8 x 75mm Carriage Bolts (83) up

 

 

 

 

through the Base (1). Note: It may be helpful to

 

83

 

 

place a piece of tape over each Carriage Bolt

 

 

 

 

 

 

 

head to hold it in place.

 

 

 

 

2. Insert the two Weight Guides (18) into the

2

 

 

 

Stabilizer (3). Make sure that the indicated

 

 

 

 

 

 

 

holes in the Weight Guides are nearer the

 

 

 

 

floor.

 

 

 

 

Attach the Stabilizer (3) and the Weight Guides

 

 

 

 

(18) to the base (1) with two M10 x 85mm Bolts

 

 

 

 

(81), two M10 Washers (80), two 21mm Steel

 

 

 

 

Spacers (108), and two M10 Nylon Locknuts (77).

 

18

 

 

Do not tighten the Nylon Locknuts yet.

 

 

 

Next, attach the Weight Guides (18) to the

 

Holes

 

 

Stabilizer (3) with two M10 x 20mm Button

 

 

 

 

Screws (96). Then, attach the Stabilizer to the

 

 

 

 

Base (1) with an M8 x 75mm Carriage Bolt (83)

 

 

 

 

and an M8 Nylon Locknut (78). Do not tighten

 

 

 

 

the Nylon Locknut yet.

 

 

 

 

Attach the Upright (2) to the Base (1) with the two

 

 

80

81

indicated M8 x 75mm Carriage Bolts (83) and two

2

78

 

 

M8 Nylon Locknuts (78). Do not tighten the

 

77

 

80

 

 

 

Nylon Locknuts yet.

 

78

 

 

 

 

 

78

 

83

3

 

 

 

 

 

 

 

 

 

1

108

 

 

 

 

 

 

 

83

96

 

 

 

 

 

3. Attach the Front Leg (10) to the Base (1) with the

3

 

 

 

two M8 x 75mm Carriage Bolts (83) and two M8

 

 

 

 

 

 

 

Nylon Locknuts (78). Do not tighten the Nylon

 

75

 

 

Locknuts yet.

 

10

 

 

104

 

 

 

 

 

Attach the Leg Lever Bumper (75) to the Front

 

110

78

 

 

 

 

Leg (10) with an M4 x 16mm Self-tapping Screw

 

 

 

 

 

 

 

(110) and an M4 Washer (104). Make sure that

 

78

 

 

the end of the Leg Lever Bumper is pointing

 

 

 

upward.

 

 

 

 

 

 

 

83

 

 

 

 

1

 

 

9

 

 

 

Image 9
Contents QUESTIONS? Model No. GGSY3066.1 Serial NoCall TOLL-FREE Table of Contents Important Precautions Before YOU Begin Right SideLeft Side 89.5mm Spacer Part Identification ChartPage Page Assembly Make Assembly EasierFour Stages of the Assembly Process Nylon Locknut yet Do not tighten the Nylon Locknuts yetNylon Locknuts yet Nylon Locknuts 78. Do not tighten the Nylon Locknuts yetRepeat this step for the Right Shroud not shown Weight Tube is oriented as shownRepeat this step for the Right Shroud Arm Assembly Repeat this step for the Left Butterfly Arm Tighten the Nylon Locknuts used in step Bend Repeat this step for the Left Press Arm not shownCable Assembly Grease Flat Edge Page Page Lever Cable 51 is under the Pulley Page 113 Knob passes through one of the holes in the Backrest Frame Repeat this step for the Left Butterfly PadPage Page Adjustment Changing the Weight SettingAttaching the Accessories Adjusting the Backrest Using the Curl PADSeat 32 can be adjusted in the same manner Locking the Weight StackWeight High Butterfly Press ARM LEG Lever LOW Pulley Weight Resistance ChartLocking the LEG Lever LbsCable Diagram Butterfly CableLeg Lever Cable Tightening the Cables MaintenanceExercise Guidelines Staying Motivated Cooling DownQty Description Part LIST-Model No. GGSY3066.17mm Spacer Grease Packet 112 M12 Nut Exploded Drawing A-Model No. GGSY3066.1 R0907A Exploded Drawing B-Model No. GGSY3066.1 R0907A Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT