JVC CA-NXHD10R manual Possible Cause Action, General

Page 86

Symptom

Possible Cause

 

Action

 

 

Tracks cannot be joined.

HDD editing

 

 

When playing back the joined

 

 

portion, you will hear noise.

 

 

 

 

 

 

•These tracks are recorded in different recording modes or in different albums.

•The total playing time of the joined track exceeds 3 hours in the Linear PCM format or 24 hours in the AAC format.

You have joined some tracks recorded from a live CD.

•This is normal. You cannot join these tracks.

•This is normal. The total playing time of a track cannot exceed these hours.

If the tracks have been recorded digitally, this cannot be avoided. To avoid this, use analog recording method when recording these tracks (see page 51). Then join them later.

Mechanical noises are heard and

the cabinet slightly vibrates.

No sound is heard.

The hard disk is constantly rotating at

This is normal.

high speed when the power is on,

 

 

causing imperceptible mechanical

 

 

noises and cabinet vibration.

 

 

 

 

 

Connections are incorrect or loose.

Check all connections and make

 

corrections (see pages 6 to 9).

 

 

 

General

Unable to operate the remote

control.

 

 

 

 

If “ERROR” appears in the main

 

display.

 

 

•The path between the remote control and the remote sensor on the unit is blocked.

•The batteries have lost their charge.

•You are using the remote control far from the main unit.

Something is wrong with your unit.

•Remove the obstruction.

•Replace the batteries (see page 9).

•Signals cannot reach the remote sensor. Move closer to the main unit.

Unplug the unit immediately, then consult your dealer.

If “ERROR! SPK DC OUT”

appears in the main display and no

sounds come from the speaker.

External keyboard does not work

at all.

Operations are disabled.

The volume is too high.

The keyboard is not fully discharged electrically.

The built-in microprocessor has malfunctioned due to external electrical interference.

Turn off the unit and unplug it, then consult your dealer.

Turn off the unit, then turn it on back again after a while.

Press REC START and 0CD on the unit at the same time, or unplug the unit then plug it back in. (See “CAUTION” below.)

DO NOT press REC START and 0CD on the unit at the same time, or do not unplug the unit then plug it back in while recording, compressing (Smart Compression) or editing the data in the HDD; otherwise, the data will be damaged.

– 81 –

Page 85 Page 87
Image 86
Page 85 Page 87
Contents CA-NXHD10R LVT0859-004AIf in Doubt Consult a Competent Electrician Class Laser Product Front view Side viewTo keep the continuity of the recorded sounds Precautions IntroductionContents Inside of Front Door Display Window Location of the ButtonsFront Panel Become familiar with the buttons on your unitDisplay Window How to open the front doorFront Panel To close the doorRemote Control When using the remote controlUnpacking Connecting AntennasGetting Started FM antennaAM MW/LW antenna Connecting SpeakersYou can connect the speakers using the speaker cords To connect an outdoor AM MW/LW antennaTo remove the speaker grille Connecting Other EquipmentEx. When connecting a cassette deck Speaker grilles are removable as shown belowPutting the Batteries into the Remote Control Connecting a keyboardFront panel Basic SettingsRemote control Turning On the Power Setting the ClockChanging the Display Contrast To adjust the clock againChanging the Display Brightness To turn on/off the clock indicationBasic and Common Operations Line Adjusting the VolumeSelecting the Sources and Starting Play To select the CD player as the source, press CD 3/8Source indication canceled Adjusting the Bass and Treble SoundsAHB 1 AHB AHB OFF canceled Reinforcing the Bass SoundWhat is AAC? Using the AAC SoundsAAC Sound OFF Mono Film canceled Hall MID Night Head PhonesListening to FM and AM MW/LW Broadcasts FM AM Line Tuning in to a StationTo change the FM reception mode To change the information shown in the main displayTo record a broadcast program automatically Presetting StationsTuning in to a Preset Station Searching for Programs by PTY Codes PTY Search Receiving FM Stations with RDSChanging the RDS Information PTYSwitching to a Program Type of Your Choice Temporarily More about the Enhanced Other Networks function Alarm functionTest function Description of the PTY codes Playing Back the External Component FM AM Adjusting the Input LevelSelecting the External Component Press SET to finish changing the source name To cancel the setting, press CancelChanging the Source Name Selected source name appears in the main displayPlaying Back CDs CD/CD-R/CD-RW Pqrs TUV WxyzPrecautions on CD Playback Playing Back the Entire CD-Normal PlayPrograming the Playing Order of the Tracks -Program Play To go to another track directly using the number buttonsBasic CD Operations To stop playback for a momentTo modify the program To check the program contentsPlaying at Random-Random Play Repeat 1TRK Repeating Tracks or CD-Repeat PlayProhibiting Disc Ejection-Disc Lock Repeat OFFPlaying Back the HDD Hard Disk Drive MarkLibraries Playing Back the Entire HDD Continuous PlayHow tracks are recorded into the HDD Press HDD 3/8Basic HDD Operations To locate a particular point in a track during playTo select another library Playing Tracks in an Album-Album PlayTo select another album HDD Album HDD LibraryTo go to another album in the same library, press Library indicator lights up on the displayTo go to another track in the same album, press ¢ or Album or Album repeatedlyRepeating Tracks-Repeat Play Random and indicators light up on the displayYou cannot cancel Repeat play during Random play All tracks in the HDD are played repeatedly and endlesslyAlbum T.? Canceled Last 10? Track title?Searching for Albums and Tracks to Play- Search Modes Track T.?Canceled Last 10? Press Enter Available symbols are as followsRepeat steps 4 1 and4 2 to enter other characters For Album Title SearchAlbum No.? To search for one of the last 10 albums recentlyPlayed or recorded-LAST Recording into the HDD How the HDD separates the recorded tracks? Before You Start RecordingAbout the digital formats used for recordings About the maximum recording length for one trackSmart COMP. CD Auto REC Using Automatic Recording FunctionsCanceled TU Auto REC Press Select ¢ or Select 4to select ON? Press SETCD Auto Recording will be automatically canceled if CD and Auto indicators light up on the displayCD and Auto indicators go off To automatically record CDs-CD Auto RecordingTU Auto REC CanceledSmart Comp CD Auto REC How Tuner Auto Recording actually works?AAC128kbps AAC 96kbps PCM x1 REC PCM x4 REC PCM x2 REC Press REC Mode on the unit to select the recording modeRecording CDs Prepare a CDEntry flashes in the main display for a while To record a single track during playbackPress SET to finish the recording To stop while recording, pressAAC128kbps AAC 96kbps When the broadcast program ends, press 7 to stop recordingRecording FM/AM MW/LW Broadcasts To assign track numbers manually while recordingStart playback on the external equipment When playback ends, press 7 to stop recordingRecording the External Component To cancel analog recording, press REC Start again To record CD into the HDD using analog recording modeWhen no sound comes in for more than 30 seconds To assign track numbers manually while recordingMaking Your Own Titles Mark 2-ABC 3-DEF GHI 5-JKL 6-MNO Pqrs 8-TUV 9-WXYZTo assign a title to an album Canceled Track EDIT?Assigning Titles to Albums and Tracks TITLE? LIB. EDIT? Album EDIT?To assign titles to tracks Press TITLE/EDIT again to exit from the title entry modeOn the remote control only Press HDD 3/8 Assign the title by referring on Press EnterEditing the HDD Mark 2-ABC 3-DEF GHI 5-JKL 6-MNO Pqrs 8-TUV 9-WXYZAlbum Editing Introducing HDD Editing FunctionsLibrary Editing Track EditingLibrary name entry screen appears in the main display Unit enters the library name entry modePress SET Press SET again Press Select ¢ or Select 4to select Restoring the Libraries-RESTORECopying an Album-COPY Album Press SET Press EnterConfirmation screen appears in the main display Moving an Album-LIB. ChangeMaking a New Album-MAKE Album Press Select ¢ or Select 4 to selectPress Select ¢ or Select 4to select ERASE?, then press SET Erasing an Album-ERASETo make your best album later Press Enter again Erasing All Albums-ALL EraseCopying a Track-COPY Track Currently selected track starts playing Press SET when you find the start point POSI.A for CopyAlbum selection screen appears Playback continues11Press Enter Moving a Track-MOVEPlayback stops, and the library selection screen appears Press Select ¢ or Select 4to select MOVE?, then press SETIf Cannot Entry LIB. appears in the main display Dividing a Track-DIVIDEPress Select ¢ or Select 4to select DIVIDE?, then press SET Playback stops Press SET when you find the dividing pointJoining Tracks-JOIN To join the divided tracks, see the Join function thatTo divide the joined tracks, see the Divide function on Erasing a Track-ERASE TRKPress Select ¢ or Select 4to select tracks If Cannot Join appears in the main displayUsing the Timers Off /TIMER SleepUsing Recording Timer How Recording Timer actually worksMinute digit starts flashing Recording source setting screen appearsFM? AM? LINE? For each recording mode, seeFM? AM? CD? Using Daily TimerHow Daily Timer actually works LINE?* HDD?To turn on the Daily Timer, repeat , and press SET in step Using Sleep TimerHow Sleep Timer actually works 120To sleep with Sleep Timer and wake up with Daily Timer Using Auto Power OffTimer Priority To deactivate Auto Power Off, press A.P.offUsing an Optional Keyboard Keys Used for Operating This UnitTo assign a track title-F2 Operating Procedures Using the KeyboardTo assign an album title-F1 To search for an album by its number-F5 To change a library name-F3To search for an album by entering its title-F6 To search for a track by entering its title-F7General Notes MaintenanceCleaning the unit Handling CDsMessage Signification SolutionMessages Signification How to rebuild the HDDCannot Possible Cause TroubleshootingCD playback Symptom ActionIf Level OVER! appears in the main display Symptom Possible Cause ActionHDD recording HDD editing Possible Cause Action GeneralSpecifications Above ALL SP-NXHD10 Connection Anschluss RemarqueAansluitingen NotaCollegamento Tilslutning

CA-NXHD10R specifications

The JVC CA-NXHD10R is a compact, versatile audio system designed to deliver high-quality sound in a sleek, modern package. This system stands out with its unique combination of features, tools, and technologies that cater to both casual listeners and audiophiles alike.

One of the main features of the CA-NXHD10R is its powerful 2-way speaker system, which produces rich and clear audio across a wide frequency range. This ensures that users can enjoy their favorite music genres, from classical to rock, with the fidelity they deserve. The system is complemented by an integrated amplifier that delivers a robust output, making it suitable for home use as well as small gatherings.

The CA-NXHD10R boasts a built-in CD player, allowing users to enjoy their CD collections without the need for additional equipment. Additionally, the system is equipped with a USB port, providing an easy way to connect USB devices and play music directly from flash drives. The inclusion of Bluetooth technology adds a contemporary touch, enabling wireless streaming from smartphones and tablets. This makes it incredibly convenient for users to access a vast library of music from popular streaming services.

For those who appreciate radio, the JVC CA-NXHD10R features an FM/AM tuner with preset station memory, allowing easy access to favorite radio channels. The system is designed with user-friendly controls, including a remote control for added convenience. The clear LCD display ensures visibility, even in low-light conditions.

In terms of design, the CA-NXHD10R is compact yet stylish, fitting seamlessly into various interior spaces. Its elegant finish and modern aesthetics make it an attractive addition to any room.

Sound customization is another highlight, with built-in equalizer settings that allow users to adjust audio to their liking. Whether it’s boosting bass or enhancing treble, this feature caters to individual preferences, ensuring a personalized listening experience.

The JVC CA-NXHD10R is designed with durability in mind, providing a reliable audio solution that withstands the test of time. Its combination of diverse input options, powerful sound delivery, and user-friendly features makes it a well-rounded choice for anyone looking to elevate their audio experience. Overall, the CA-NXHD10R is an excellent option for those seeking a high-performance, aesthetically pleasing sound system.
Top Page Image Contents