Bushnell 20-1925 manual Operational Summary, Features

Page 6

OPERATIONAL SUMMARY

While looking through the monocular, depress the power button once to activate the inview display system (LCD). Aim the Yardage Pro X500 at a target at least 5 yards away, depress and hold the power button down until range reading is displayed. Release the power button.

Note: Once activated, the Yardage Pro X500’s LCD will remain active and display the last distance measurement for 30 seconds. You can depress the power button again at any time to distance to a new target. As with any laser device, it is not recommended to directly view the emissions for long periods of time with magnified lenses.

FEATURES

Your Yardage Pro X500’s LCD incorporates illuminated indicators that advise you unit of measure, when the laser is active, the battery charge is low, and when a target has been acquired. A summary of these features is presented below:

UNIT OF MEASURE OPTIONS – The Yardage Pro X500 can be used to measure distances in yards or meters. The unit of measure indicators are located in the lower right portion of the LCD. To select between yards and meters, remove the battery cover slide. Locate the internal yards to meter slide switch. To measure in yards, slide the switch to the “Y” position. To measure in meters, slide the switch to the “M” position.

ILLUMINATING INDICATORS – Low Battery Charge ( ) When the low battery symbol is displayed in the upper right-hand portion of the LCD, the battery charge is getting low and the 9-volt alkaline battery should be replaced.

Target Acquired: Informs the user that a distance measurement has been obtained. The message “TARGET ACQUIRED” will appear in the top portion of the LCD. The distance measured will appear at the bottom of the LCD in numerical form.

4

Image 6
Contents Model Lit. # 98-0738/03-06 Page Contents English Introduction Features Operational SummarySpecifications Weight 7.4 oz Accuracy +/- 1 yard MagnificationCleaning Warranty / Repair TWO-YEAR Limited Warranty U.S.A. Send To Canada Send ToTrouble Shooting Table If unit does not turn on LCD does not illuminateIf target range cannot be obtained FCC Note Page Français Introduction Fonctionnement EN Bref CaractéristiquesSpécifications EntretienGarantie / Réparation Garantie Limitée DE Deux ANS Aux États-UnisAu Canada Tableau DE Dépannage La mesure de la distance ne peut être obtenuePage Page Español Introducción Resumen DE Funcionamiento CaracterísticasEspecificaciones LimpiezaGarantía / Reparación Garantía Limitada DE DOS Años EN EE.UU. enviar a EN CANADÁ, enviar aTabla DE Localización DE Fallos Si la unidad no se enciende la pantalla LCD no se iluminaSi no se puede obtener la distancia hasta el blanco Nota DE FCC Page Deutsch An- und AusschalterEinführung Kurzzusammenfassung Gerätebedienung Technische EigenschaftenVergrößerung 4-fach SpezifikationenGewicht 7.4 oz ReinigungGewährleistung / Reparatur Zweijährige Gewährleistungsfrist Versandadresse für die U.S.A Versandadresse für KanadaTabelle ZUR Fehlersuche Wenn das Gerät nicht einschaltet LCD leuchtet nicht aufHinweis ZU FCC Richtlinien Page Italiano Introduzione Istruzioni Sommarie PER L’USO CaratteristicheDati Tecnici Precisione +/- 1 metro Ingrandimento PuliziaGaranzia / Riparazioni Garanzia Limitata DI DUE Anni Canada Inviare a Bushnell Outdoor Products Attn RepairsRisoluzione DEI Problemi Se l’unità non si accende L’LCD non si illuminaSe non è possibile ottenere la distanza di un bersaglio Annotazione FCC Page Português Introdução Resumo Operacional Especificações AmpliaçãoLimpeza Garantia / Conserto Garantia Limitada DE Dois Anos Nos EUA envie para No Canadá envie paraTabela DE Identificação E Solução DE Problemas Unidade não liga o LCD não acendeSe a leitura da distância do alvo não puder ser obtida Nota DA FCC Page Bushnell Outdoor Products
Related manuals
Manual 52 pages 5.22 Kb