JVC GVT0104-002A Connecting Speakers, To connect an outdoor AM antenna, To connect speakers

Page 10

English

AM antenna

1

2

ANTENNA

Vinyl-covered wire

(not supplied)

3

AM loop antenna

(supplied)

1If the cords are covered with insulation, remove a short section of insulation at the end of each cord by twisting and pulling it off.

2Connect the AM loop antenna to the AM LOOP terminals as illustrated.

3Turn the AM loop antenna until you have the best reception.

To connect an outdoor AM antenna

When reception is poor, connect a single vinyl-covered wire to the AM EXT terminal and extend it horizontally. The AM loop antenna must remain connected.

For better reception of both FM and AM

•Make sure the antenna conductors do not touch any other terminals or connecting cords.

•Keep the antennas away from metallic parts of the unit, connecting cords, and the AC power cord.

Connecting Speakers

To connect speakers

You can connect the speakers using the speaker cords.

1
2		3,4
SPEAKERS
RIGHT	LEFT	Red
Speaker		Speaker
cord	SPEAKER	cord
	IMPEDANCE
	4Ω ~ 16Ω
Black
Right speaker		Left speaker

1If the cords are covered with insulation, remove a short section of insulation at the end of each cord by twisting and pulling it off.

2Hold the clamp of the speaker terminal.

3Insert the end of the speaker cord into the

terminal.

Match the polarity of the speaker terminals: Red cord to red terminal ª and black cord to black terminal ·.

4Release your finger from the clamp.

IMPORTANT:

•Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the unit.

•DO NOT connect more than one speaker to one speaker terminal.

7

Image 10

Contents CA-UXJ55MD Page Important for Laser Products Introduction PrecautionsAbout This Manual Contents Front Panel Location of the Buttons and ControlsFront panel Display window on the front panel Display windowRemote Control See pages in parentheses for detailsUnpacking Connecting AntennasGetting Started FM antennaTo connect an outdoor AM antenna Connecting SpeakersAM antenna To connect speakersTo connect external equipment Connecting External EquipmentPutting the Batteries into the Remote Control To play the other equipment through this unit, connectTo change the clock again Setting the ClockBasic and Common Operations To check the clock time with tonesTurning On/Off the Key-touch Tone To turn off the clock indication Power SaveOn the remote control To turn off the unit automatically Auto StandbyAdjusting the Volume Level Reinforcing the Bass SoundChanging the Display Brightness Adjusting the TonePress BASS/TREBLE to adjust the Bass Bass or treble levelListening to FM and AM Broadcasts Tuning in to a StationTo change the FM reception mode Press and hold ¢or 4for more than 1 secondPresetting Stations Tuning in to a Preset StationPlaying Back All the Discs Continuous Play When playing a CD-R or CD-RWPlaying Back Discs on the 5-CD Changer Loading DiscsTo start playing a disc during playback of another disc Basic Disc OperationsTo change a disc during playback of another disc To locate a particular point in a track during playPrograming the Track Playing Order -Program Play To go to another track directly using the number buttonsTo change the information shown on the display To modify the program To check the program contentsPlaying at Random-Random Play To erase the entire programProhibiting Disc Ejection-Disc Lock Repeat PlayBasic MD Operations Playing Back MDsPlaying Back the Entire MD -Normal Play To stop play for a momentWhen the MD recorder stops While playing or pausingPress ¢or 4repeatedly Press the number buttons to select the tracks Load an MDUntil MD Program appears On the display Repeat to program other tracks you wantLoad an MD including groups Playing Tracks in a Group-Group PlayUntil MD Random appears On the display Until MD Group appears on DisplayPress Title Search Repeating Tracks-Repeat PlaySearching for Tracks to Play MD Title Search Enter the characters to search for the trackTo prohibit MD ejection-MD Lock Available symbols are as followsPress Enter To enter a C or c, pressPlaying Back a Tape To play both sides-Reverse ModePlaying Back Tapes Press Tape 2Listening to External Equipment Listening to External EquipmentAbout the track marks Recording on MDsBefore You Start Recording on an MD To avoid erasing important recordingsAbout High-Speed Recording Precautions for performing long-hour stereo recordingStereo Long-Hour Recording Mdlp To check the remaining recording timeTo set the recording length mode Setting MD Recording ModesTo set group recording mode To set LP-prefix addition modePress MD REC when the selected Press CD REC Mode to select the CD RECRecording mode Recording mode in is still Shown on the displayPrepare the source to record from Press CD REC Mode to selectTrack mark entry mode Press MD RECTo protect your recordings Recording on TapesBefore You Start Recording on a Tape To keep the best recording and playback sound qualityRecording onto a Tape Reverse modeRecording CD onto a Tape CD-Tape Synchronized Recording Press Tape REC whenTo record a single track of a CD/MD during play Press Tape RECFor the MD CD Synchronized RecordingPress MD&TAPE REC For the cassetteEditing MDs Using MD Groups as a separate itemHow to make up Groups Guidance-MD Group FunctionsIntroducing Group Editing Functions Forming a Group-FORM GR Repeatedly until Entry GR ? Appears on the display To cancel the setting, press CANCEL, then repeat fromYou can also select the track using TrackTrack as the dividing Point Dividing a Group-DIVIDE GRRepeatedly until Divide GR? Appears on the display To join the divided groups, see the Join GR function onJoining Two Groups-JOIN GR When Cannot Join appears on the display in stepRepeatedly until Join GR ? Appears on the display Press Group Skip ¢or Group Skip Moving a Group-MOVE GRRepeatedly until Move GR ? Appears on the display 4while holding Shift to select the groupDissolving All Groups-UNGR ALL To cancel the setting, press CancelUngrouping Tracks-UNGROUP Repeatedly until Ungroup ? Appears on the displayErasing Tracks in a Group-ERASE GR Repeatedly until Erase GR ? Appears on the displayIntroducing Track Editing Functions Dividing a Track-DIVIDE Loading slot Joining Two Tracks-JOINInsert an MD you want to edit into the MD Until Join ? appears on DisplayUntil Move ? appears on Display Position where you want To move the track toMoving a Track-MOVE Track you want to moveUntil ERASE? appears on Display Erasing Tracks-ERASEErasing All Tracks-ALL Erase Track you want to eraseAssigning Titles to an MD Title entry modeSelected title entry mode Press or To changePress Enter to finish the current Press Cancel to exit fromEnter characters Title entrySelect the character you Changing the TitleFollow steps 1 to 4 on Want to correct, by pressingUsing Recording Timer Using the TimersHow Recording Timer actually works Set the start time Set the shut-off timePress CLOCK/TIMER repeatedly Using Daily TimerHow Daily Timer actually works Until Daily Timer appearsTo adjust the volume level Adjust the volume levelVolume setting appears on Display To turn off the Daily Timer after its setting is doneTimer Priority Using Sleep TimerHow Sleep Timer actually works To clean the disc MaintenanceStains on the unit English Hcms High-speed Copy Management System Scms Serial Copy Management SystemMD limitations Cannot REC x1 REC only CD/MD MessagesCannot REC x1 or x2 only Troubleshooting NON Audio or DVDSpecifications EN, CS Victor Company of JAPAN, Limited 0803AIMMDWJEM