JVC CA-UXJ55MD Recording on Tapes, Before You Start Recording on a Tape, To demagnetize the head

Page 36

English

Recording on Tapes

Before You Start Recording on a Tape

It may be unlawful to record or play back copyrighted material without the consent of the copyright owner.

The recording level is automatically set correctly, so it is not affected by the volume level. Thus, during recording you can adjust the sound you are actually listening to without affecting the recording level.

While recording, you can hear sound mode effect and/or the AHB PRO (Active Hyper Bass PRO) effect through the speakers or headphones. However, the sound is recorded without these effects (see pages 11 and 12).

If recordings you have made have excessive noise or static, the unit may be too close to a TV. Place the unit away from the TV.

You can use only type I tapes for recording.

To protect your recordings

Cassettes have two small taps on the back to protect unexpected erasure or recording.

To protect your recording, remove these tabs.

To re-record on a protected tape, cover the holes with adhesive tape.

Adhesive tape

The use of the C-120 or longer tape is not recommended, since characteristic deterioration may occur and this tape easily jams in the pinch rollers and the capstans.

To keep the best recording and playback sound quality

You need to clean the heads.

Clean the heads after every 10 hours of use with

a wet-type head cleaning tape (available at electronic and audio shops).

When the head becomes dirty, the following symptoms will occur:

Sound quality is reduced.

Sound level decreases.

Sound drops out.

Do not play dirty or dusty tapes.

Do not touch the highly-polished head with any metallic or magnetic tools.

To demagnetize the head

Turn off (on standby) the unit, and use a head demagnetizer (available at electronics and audio shops).

At the start and end of cassette tapes

There is leader tape which cannot be recorded onto. Thus, when recording discs, MDs, or radio broadcasts, wind the leader tape first to ensure that the recording will be made without any music part lost.

33

Image 36
Contents CA-UXJ55MD Page Important for Laser Products Precautions IntroductionAbout This Manual Contents Location of the Buttons and Controls Front PanelFront panel Display window on the front panel Display windowRemote Control See pages in parentheses for detailsConnecting Antennas Getting StartedUnpacking FM antennaConnecting Speakers AM antennaTo connect an outdoor AM antenna To connect speakersConnecting External Equipment Putting the Batteries into the Remote ControlTo connect external equipment To play the other equipment through this unit, connectSetting the Clock Basic and Common OperationsTo change the clock again To check the clock time with tonesTo turn off the clock indication Power Save On the remote controlTurning On/Off the Key-touch Tone To turn off the unit automatically Auto StandbyAdjusting the Volume Level Reinforcing the Bass SoundAdjusting the Tone Press BASS/TREBLE to adjust the BassChanging the Display Brightness Bass or treble levelTuning in to a Station To change the FM reception modeListening to FM and AM Broadcasts Press and hold ¢or 4for more than 1 secondPresetting Stations Tuning in to a Preset StationWhen playing a CD-R or CD-RW Playing Back Discs on the 5-CD ChangerPlaying Back All the Discs Continuous Play Loading DiscsBasic Disc Operations To change a disc during playback of another discTo start playing a disc during playback of another disc To locate a particular point in a track during playTo go to another track directly using the number buttons Programing the Track Playing Order -Program PlayTo change the information shown on the display To check the program contents Playing at Random-Random PlayTo modify the program To erase the entire programProhibiting Disc Ejection-Disc Lock Repeat PlayPlaying Back MDs Playing Back the Entire MD -Normal PlayBasic MD Operations To stop play for a momentWhile playing or pausing When the MD recorder stopsPress ¢or 4repeatedly Load an MD Until MD Program appears On the displayPress the number buttons to select the tracks Repeat to program other tracks you wantPlaying Tracks in a Group-Group Play Until MD Random appears On the displayLoad an MD including groups Until MD Group appears on DisplayRepeating Tracks-Repeat Play Searching for Tracks to Play MD Title SearchPress Title Search Enter the characters to search for the trackAvailable symbols are as follows Press EnterTo prohibit MD ejection-MD Lock To enter a C or c, pressTo play both sides-Reverse Mode Playing Back TapesPlaying Back a Tape Press Tape 2Listening to External Equipment Listening to External EquipmentRecording on MDs Before You Start Recording on an MDAbout the track marks To avoid erasing important recordingsPrecautions for performing long-hour stereo recording Stereo Long-Hour Recording MdlpAbout High-Speed Recording To check the remaining recording timeSetting MD Recording Modes To set group recording modeTo set the recording length mode To set LP-prefix addition modePress CD REC Mode to select the CD REC Recording modePress MD REC when the selected Recording mode in is still Shown on the displayPress CD REC Mode to select Track mark entry modePrepare the source to record from Press MD RECRecording on Tapes Before You Start Recording on a TapeTo protect your recordings To keep the best recording and playback sound qualityReverse mode Recording CD onto a Tape CD-Tape Synchronized RecordingRecording onto a Tape Press Tape REC whenTo record a single track of a CD/MD during play Press Tape RECCD Synchronized Recording Press MD&TAPE RECFor the MD For the cassetteUsing MD Groups as a separate item How to make up GroupsEditing MDs Guidance-MD Group FunctionsIntroducing Group Editing Functions Forming a Group-FORM GR To cancel the setting, press CANCEL, then repeat from You can also select the track usingRepeatedly until Entry GR ? Appears on the display TrackDividing a Group-DIVIDE GR Repeatedly until Divide GR? Appears on the displayTrack as the dividing Point To join the divided groups, see the Join GR function onWhen Cannot Join appears on the display in step Joining Two Groups-JOIN GRRepeatedly until Join GR ? Appears on the display Moving a Group-MOVE GR Repeatedly until Move GR ? Appears on the displayPress Group Skip ¢or Group Skip 4while holding Shift to select the groupTo cancel the setting, press Cancel Ungrouping Tracks-UNGROUPDissolving All Groups-UNGR ALL Repeatedly until Ungroup ? Appears on the displayErasing Tracks in a Group-ERASE GR Repeatedly until Erase GR ? Appears on the displayIntroducing Track Editing Functions Dividing a Track-DIVIDE Joining Two Tracks-JOIN Insert an MD you want to edit into the MDLoading slot Until Join ? appears on DisplayPosition where you want To move the track to Moving a Track-MOVEUntil Move ? appears on Display Track you want to moveErasing Tracks-ERASE Erasing All Tracks-ALL EraseUntil ERASE? appears on Display Track you want to eraseTitle entry mode Selected title entry modeAssigning Titles to an MD Press or To changePress Cancel to exit from Enter charactersPress Enter to finish the current Title entryChanging the Title Follow steps 1 to 4 onSelect the character you Want to correct, by pressingUsing the Timers Using Recording TimerHow Recording Timer actually works Set the start time Set the shut-off timeUsing Daily Timer How Daily Timer actually worksPress CLOCK/TIMER repeatedly Until Daily Timer appearsAdjust the volume level Volume setting appears on DisplayTo adjust the volume level To turn off the Daily Timer after its setting is doneUsing Sleep Timer Timer PriorityHow Sleep Timer actually works Maintenance To clean the discStains on the unit English Scms Serial Copy Management System Hcms High-speed Copy Management SystemMD limitations CD/MD Messages Cannot REC x1 REC onlyCannot REC x1 or x2 only Troubleshooting NON Audio or DVDSpecifications EN, CS Victor Company of JAPAN, Limited 0803AIMMDWJEM